Inital commit

Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
2026-09-24 06:10:13 +01:00 · 2023-02-09 00:44:25 +02:00
parent 17aa45316b
commit 31713f34f6
263 changed files with 35669 additions and 2029 deletions
@@ -2,129 +2,125 @@

 Supported machines:

-* `mcm-imxi8-mini`
-* `ucm-imxi8-mini`
-* `iot-gate-imx8`
+* `IOT-GATE-iMX8`

 Define a `MACHINE` environment variable for the target product:

 |Machine|Command Line|
 |---|---|
-|mcm-imx8m-mini|export MACHINE=mcm-imx8m-mini
-|ucm-imx8m-mini|export MACHINE=ucm-imx8m-mini
-|iot-gate-imx8|export MACHINE=iot-gate-imx8
+|ucm-imx8m-mini|export MACHINE=iot-gate-imx8

 Define the following environment variables:

 |Description|Command Line|
 |---|---|
-|NXP u-boot release|export NXP_UBOOT_RELEASE=lf-5.10.35-2.0.0|
-|NXP ATF release|export NXP_ATF_RELEASE=lf-5.10.35-2.0.0|
-|NXP mkimage release|export NXP_MKIMAGE_RELEASE=lf-5.10.35-2.0.0|
-|NXP firmware name|export NXP_FIRMWARE=firmware-imx-8.12.bin|
-|CompuLab branch name|export CPL_BRANCH=rel_imx_5.10.35_2.0.0-stable|
-
+|NXP firmware name|export NXP_FIRMWARE=firmware-imx-8.14.bin|
+|CompuLab release|export CPL_RELEASE=${MACHINE}_r3.1|
+|CompuLab branch name|export CPL_BRANCH=lf-5.10.72-2.2.0_${MACHINE}|
+|ATF revision|export ATF=lf-5.10.72-2.2.0|
+|OPTEE revision|export OPTEE=lf-5.10.72-2.2.0|
+|U-Boot revision|export UBOOT=lf-5.10.72-2.2.0|

 ## Prerequisites
 It is up to developer to setup arm64 build environment:
-* Download and install the [GNU tool chain](https://github.com/compulab-yokneam/meta-bsp-imx8mm/blob/rel_imx_5.10.35_2.0.0-experiment/Documentation/toolchain.md)
-
+* Download the [ARM tool chain](https://developer.arm.com/tools-and-software/open-source-software/developer-tools/gnu-toolchain/gnu-a/downloads/9-2-2019-12)
+* Set environment variables:
+<pre>
+export ARCH=arm64
+export CROSS_COMPILE=/opt/gcc-arm-9.2-2019.12-x86_64-aarch64-none-linux-gnu/bin/aarch64-none-linux-gnu-
+</pre>
 * Create a folder to organize the files:
 <pre>
-mkdir imx8mm
-cd imx8mm
-export SRC_ROOT=$(pwd)
+mkdir -p imx8mm/{sources,results}
+export SRC_ROOT=$(readlink -f imx8mm/sources)
+export RESULTS=$(readlink -f imx8mm/results)
+cd ${SRC_ROOT}
 </pre>

 * Download CompuLab BSP
 <pre>
-git clone -b ${CPL_BRANCH} https://github.com/compulab-yokneam/meta-bsp-imx8mm.git
+git clone -b ${CPL_RELEASE} https://github.com/compulab-yokneam/meta-bsp-imx8mm.git
 export LAYER_DIR=$(pwd)/meta-bsp-imx8mm
 </pre>

-## Mkimage setup
-* Download the mkimage:
-<pre>
-git clone https://source.codeaurora.org/external/imx/imx-mkimage.git
-git -C imx-mkimage checkout ${NXP_MKIMAGE_RELEASE}
-</pre>
-
-## Arm Trusted Firmware (ATF) setup
-* Download the ATF:
-<pre>
-git clone https://source.codeaurora.org/external/imx/imx-atf.git
-git -C imx-atf checkout ${NXP_ATF_RELEASE}
-git -C imx-atf am ${LAYER_DIR}/recipes-bsp/imx-atf/compulab/imx8mm/*.patch
-</pre>
-* Make bl31.bin
-<pre>
-make -C imx-atf PLAT=imx8mm bl31
-cp -v imx-atf/build/imx8mm/release/bl31.bin ${SRC_ROOT}/imx-mkimage/iMX8M/
-</pre>
-
-## Firmware iMX setup
+## Build Procedure
+### Firmware iMX setup
 * Download the firmware-imx file:
 <pre>
 wget http://www.freescale.com/lgfiles/NMG/MAD/YOCTO/${NXP_FIRMWARE}
 bash -x ${NXP_FIRMWARE} --auto-accept
-cp -v $(find firmware* | awk '/train|hdmi_imx8|dp_imx8/' ORS=" ") ${SRC_ROOT}/imx-mkimage/iMX8M/
+cp -v $(find firmware* | awk '/train|hdmi_imx8|dp_imx8/' ORS=" ") ${RESULTS}
 </pre>

-## U-Boot
-* Download the U-Boot source and apply CompuLab BSP patches:
+### Arm Trusted Firmware (ATF) setup
+* Download the ATF:
 <pre>
-git clone https://source.codeaurora.org/external/imx/uboot-imx.git
-git -C uboot-imx checkout ${NXP_UBOOT_RELEASE}
-git -C uboot-imx am ${LAYER_DIR}/recipes-bsp/u-boot/compulab/imx8mm/*.patch
+git clone https://source.codeaurora.org/external/imx/imx-atf.git
+git -C imx-atf checkout ${ATF} -b ${CPL_BRANCH}
 </pre>
-
-* Compile U-Boot:
+* Apply patches if applicable:
 <pre>
-make -C uboot-imx -f defconfig.mk
-make -C uboot-imx
+[[ -d ${LAYER_DIR}/recipes-bsp/imx-atf/compulab/imx8mm ]] && { \
+git -C imx-atf am ${LAYER_DIR}/recipes-bsp/imx-atf/compulab/imx8mm/*.patch
+}
 </pre>
+* Make bl31.bin

-* Copy files to the mkimage directory:
+|Mode |Command
+|---|---|
+|optee build|make -j 16 -C imx-atf PLAT=imx8mm BUILD_BASE=build PLAT=imx8mm IMX_BOOT_UART_BASE=0x30880000 BL32_BASE=0x56000000 BL32_SIZE=0x2000000 SPD=opteed bl31
+|non-optee build|make -j 16 -C imx-atf PLAT=imx8mm BUILD_BASE=build PLAT=imx8mm IMX_BOOT_UART_BASE=0x30880000 BL32_BASE=0x56000000 BL32_SIZE=0x2000000 bl31
+
+* Ceate a symlink in the ${RESULTS} folder:
 <pre>
-cp -v $(find uboot-imx | awk -v v=${MACHINE} '(/u-boot-spl.bin$|u-boot.bin$|u-boot-nodtb.bin$|tools\/mkimage$/)||($0~v".dtb$")' ORS=" ") ${SRC_ROOT}/imx-mkimage/iMX8M/
+ln -s $(readlink -f imx-atf/build/imx8mm/release/bl31.bin) ${RESULTS}/
 </pre>

-<!---
-## OP-TEE Setup
-Download the OP-TEE from:
+### OP-TEE Setup
+
+| Skip this for a non-optee build |
+| --- |
+
+* Download the OP-TEE:
 <pre>
 git clone https://source.codeaurora.org/external/imx/imx-optee-os
-git -C imx-optee-os checkout ${NXP_RELEASE} -b ${CPL_BRANCH}
-git -C imx-atf am ${LAYER_DIR}/recipes-security/optee-imx/compulab/imx8mm/*.patch
+git -C imx-optee-os checkout ${OPTEE} -b ${CPL_BRANCH}
+</pre>
+* Apply patches if applicable:
+<pre>
+[[ -d ${LAYER_DIR}/recipes-security/optee-imx/compulab/imx8mm ]] && { \
+git -C imx-optee-os am ${LAYER_DIR}/recipes-security/optee-imx/compulab/imx8mm/*.patch
+}
 </pre>
-
 * Set environment variables:
 <pre>
 export ARCH=arm
-export CROSS_COMPILE=/usr/bin/arm-linux-gnu-
-export CROSS_COMPILE64=/usr/bin/arm-linux-gnu-
+export CROSS_COMPILE64=${CROSS_COMPILE}
 </pre>
-
 * Make tee.bin
 <pre>
-cd imx-optee-os
-./scripts/imx_build.sh mx8mmevk
-cp -v build.mx8mmevk/core/tee.bin ${SRC_ROOT}/imx-mkimage/iMX8M/
+make -j 16 -C imx-optee-os PLATFORM=imx PLATFORM_FLAVOR=mx8mm_cl_iot_gate
+ln -s $(readlink -f imx-optee-os/out/arm-plat-imx/core/tee-raw.bin) ${RESULTS}/tee.bin
 </pre>
-->

-## Compiling the **flash.bin** imx-boot image:
-* Unset these variables:
+### U-Boot
+* Download the U-Boot source and apply CompuLab BSP patches:
 <pre>
-unset ARCH CROSS_COMPILE
+git clone https://source.codeaurora.org/external/imx/uboot-imx.git
+git -C uboot-imx checkout ${UBOOT} -b ${CPL_BRANCH}
+git -C uboot-imx am ${LAYER_DIR}/recipes-bsp/u-boot/compulab/imx8mm/*.patch
 </pre>
-* Issue:
+* Restore `ARCH` environment variables:
 <pre>
-cd ${SRC_ROOT}/imx-mkimage/iMX8M
-sed "s/\(^dtbs = \).*/\1${MACHINE}.dtb/;s/\(mkimage\)_uboot/\1/" soc.mak > Makefile
-make clean
-make flash_evk SOC=iMX8MM
+export ARCH=arm64
+</pre>
+* Compile U-Boot flash.bin:
+<pre>
+make -j 16 -C uboot-imx O=${RESULTS} -f defconfig.mk
+make -j 16 -C uboot-imx O=${RESULTS}
 </pre>

 ## Flashing
-`dd if=flash.bin of=/dev/<your device> bs=1K seek=33 status=progress`
+<pre>
+dd if=${RESULTS}/flash.bin of=/dev/<your device> bs=1K seek=33 status=progress
+</pre>
@@ -0,0 +1,156 @@
+# Building Boot Firmware for CompuLab's i.MX8M Mini products with Mkimage
+
+Supported machines:
+
+* `IOT-GATE-iMX8`
+
+Define a `MACHINE` environment variable for the target product:
+
+|Machine|Command Line|
+|---|---|
+|ucm-imx8m-mini|export MACHINE=iot-gate-imx8
+
+Define the following environment variables:
+
+|Description|Command Line|
+|---|---|
+|NXP firmware name|export NXP_FIRMWARE=firmware-imx-8.14.bin|
+|CompuLab release|export CPL_RELEASE=${MACHINE}_r3.0|
+|CompuLab branch name|export CPL_BRANCH=lf-5.10.72-2.2.0_${MACHINE}|
+|Mkimage revision|export MKIMG=lf-5.10.72-2.2.0|
+|ATF revision|export ATF=lf-5.10.72-2.2.0|
+|OPTEE revision|export OPTEE=lf-5.10.72-2.2.0|
+|U-Boot revision|export UBOOT=lf-5.10.72-2.2.0|
+
+## Prerequisites
+It is up to developer to setup arm64 build environment:
+* Download the [ARM tool chain](https://developer.arm.com/tools-and-software/open-source-software/developer-tools/gnu-toolchain/gnu-a/downloads/9-2-2019-12)
+* Set environment variables:
+<pre>
+export ARCH=arm64
+export CROSS_COMPILE=/opt/gcc-arm-9.2-2019.12-x86_64-aarch64-none-linux-gnu/bin/aarch64-none-linux-gnu-
+</pre>
+* Create a folder to organize the files:
+<pre>
+mkdir -p imx8mm
+export SRC_ROOT=$(readlink -f imx8mm)
+cd ${SRC_ROOT}
+</pre>
+
+* Download CompuLab BSP
+<pre>
+git clone -b ${CPL_RELEASE} https://github.com/compulab-yokneam/meta-bsp-imx8mm.git
+export LAYER_DIR=$(pwd)/meta-bsp-imx8mm
+</pre>
+
+## Build Procedure
+### Mkimage setup
+* Download the mkimage:
+<pre>
+git clone https://source.codeaurora.org/external/imx/imx-mkimage.git
+git -C imx-mkimage checkout ${MKIMG}
+export RESULTS=${SRC_ROOT}/imx-mkimage/iMX8M
+</pre>
+
+### Firmware iMX setup
+* Download the firmware-imx file:
+<pre>
+wget http://www.freescale.com/lgfiles/NMG/MAD/YOCTO/${NXP_FIRMWARE}
+bash -x ${NXP_FIRMWARE} --auto-accept
+cp -v $(find firmware* | awk '/train|hdmi_imx8|dp_imx8/' ORS=" ") ${RESULTS}
+</pre>
+
+### Arm Trusted Firmware (ATF) setup
+* Download the ATF:
+<pre>
+git clone https://source.codeaurora.org/external/imx/imx-atf.git
+git -C imx-atf checkout ${ATF} -b ${CPL_BRANCH}
+</pre>
+* Apply patches if applicable:
+<pre>
+[[ -d ${LAYER_DIR}/recipes-bsp/imx-atf/compulab/imx8mm ]] && { \
+git -C imx-atf am ${LAYER_DIR}/recipes-bsp/imx-atf/compulab/imx8mm/*.patch
+}
+</pre>
+* Make bl31.bin
+
+|Mode |Command
+|---|---|
+|optee build|make -j 16 -C imx-atf PLAT=imx8mm BUILD_BASE=build PLAT=imx8mm IMX_BOOT_UART_BASE=0x30880000 BL32_BASE=0x56000000 BL32_SIZE=0x2000000 SPD=opteed bl31
+|non-optee build|make -j 16 -C imx-atf PLAT=imx8mm BUILD_BASE=build PLAT=imx8mm IMX_BOOT_UART_BASE=0x30880000 BL32_BASE=0x56000000 BL32_SIZE=0x2000000 bl31
+
+* Ceate a symlink in the ${RESULTS} folder:
+<pre>
+ln -s $(readlink -f imx-atf/build/imx8mm/release/bl31.bin) ${RESULTS}/
+</pre>
+
+### OP-TEE Setup
+
+| Skip this for a non-optee build |
+| --- |
+
+* Download the OP-TEE:
+<pre>
+git clone https://source.codeaurora.org/external/imx/imx-optee-os
+git -C imx-optee-os checkout ${OPTEE} -b ${CPL_BRANCH}
+</pre>
+* Apply patches if applicable:
+<pre>
+[[ -d ${LAYER_DIR}/recipes-security/optee-imx/compulab/imx8mm ]] && { \
+git -C imx-optee-os am ${LAYER_DIR}/recipes-security/optee-imx/compulab/imx8mm/*.patch
+}
+</pre>
+* Set environment variables:
+<pre>
+export ARCH=arm
+export CROSS_COMPILE64=${CROSS_COMPILE}
+</pre>
+* Make tee.bin
+<pre>
+make -j 16 -C imx-optee-os PLATFORM=imx PLATFORM_FLAVOR=mx8mm_cl_iot_gate
+ln -s $(readlink -f imx-optee-os/out/arm-plat-imx/core/tee-raw.bin) ${RESULTS}/tee.bin
+</pre>
+
+### U-Boot
+* Download the U-Boot source and apply CompuLab BSP patches:
+<pre>
+git clone https://source.codeaurora.org/external/imx/uboot-imx.git
+git -C uboot-imx checkout ${UBOOT} -b ${CPL_BRANCH}
+git -C uboot-imx am ${LAYER_DIR}/recipes-bsp/u-boot/compulab/imx8mm/*.patch
+</pre>
+* Restore `ARCH` environment variables:
+<pre>
+export ARCH=arm64
+</pre>
+* Compile U-Boot flash.bin:
+<pre>
+make -j 16 -C uboot-imx -f defconfig.mk
+make -j 16 -C uboot-imx
+</pre>
+* Copy files to the results directory
+<pre>
+cp -v $(find uboot-imx | awk -v v=${MACHINE} '(/u-boot-spl.bin$|u-boot.bin$|u-boot-nodtb.bin$|tools\/mkimage$/)||($0~v".dtb$")' ORS=" ") ${RESULTS}
+</pre>
+### Compiling the flash.bin imx-boot image
+* Unset these variables:
+<pre>
+unset ARCH CROSS_COMPILE
+</pre>
+Issue:
+<pre>
+cd ${RESULTS}
+sed "s/\(^dtbs \).*/\1= ${MACHINE}.dtb/;s/\(mkimage\)_uboot/\1/;s/\(^TEE_LOAD_ADDR \).*/\1= 0x56000000/g" soc.mak > Makefile
+make clean
+make flash_evk SOC=iMX8MM
+</pre>
+Issue the following commands to generate log files for the HAB signing operation:
+<pre>
+make SOC=iMX8MM flash_evk 2>&1 | tee flash_evk.log
+make SOC=iMX8MM print_fit_hab 2>&1 | tee print_fit_hab.log
+</pre>
+## Flashing
+<pre>
+echo 0 > /sys/class/block/mmcblk2boot0/force_ro
+dd if=flash.bin of=/dev/mmcblk2boot0 bs=1K seek=33 status=progress
+echo 1 > /sys/class/block/mmcblk2boot0/force_ro
+</pre>
@@ -2,26 +2,24 @@

 Supported machines:

-* `mcm-imx8m-mini`
-* `ucm-imx8m-mini`
+* `iot-gate-imx8`

 Define a `MACHINE` environment variable for the target product:

 |Machine|Command Line|
 |---|---|
-|mcm-imx8m-mini|export MACHINE=mcm-imx8m-mini
-|ucm-imx8m-mini|export MACHINE=ucm-imx8m-mini
+|iot-gate-imx8|export MACHINE=iot-gate-imx8

 Define the following environment variables:

 |Description|Command Line|
 |---|---|
-|NXP release name|export NXP_RELEASE=lf-5.10.35-2.0.0|
-|CompuLab branch name|export CPL_BRANCH=rel_imx_5.10.35_2.0.0-stable|
+|NXP release name|export NXP_RELEASE=lf-5.10.y|
+|CompuLab branch name|export CPL_BRANCH=iot-gate-imx8_r3.0|

 ## Prerequisites
 It is up to developer to setup arm64 build environment:
-* Download the [GNU tool chain](https://github.com/compulab-yokneam/meta-bsp-imx8mm/blob/rel_imx_5.4.70_2.3.0-stable/Documentation/toolchain.md)
+* Download the [GNU tool chain](https://github.com/compulab-yokneam/meta-bsp-imx8mm/blob/iot-gate-imx8_r3.0/Documentation/toolchain.md)
 * Create a folder to organize the files:
 <pre>
 mkdir imx8mm
@@ -35,13 +33,13 @@ export PATCHES=$(pwd)/meta-bsp-imx8mm/recipes-kernel/linux/compulab/imx8mm

 ## CompuLab Linux Kernel setup
 <pre>
-git clone https://source.codeaurora.org/external/imx/linux-imx.git
-git -C linux-imx checkout -b linux-compulab ${NXP_RELEASE}
+git clone -b ${NXP_RELEASE} --single-branch https://source.codeaurora.org/external/imx/linux-imx.git
+git -C linux-imx checkout -b linux-compulab 
 git -C linux-imx am ${PATCHES}/*.patch
 </pre>

 ## Compile the Kernel
 <pre>
-make -C linux-imx cl-imx8m-mini_defconfig ${MACHINE}.config
+make -C linux-imx ${MACHINE}_defconfig
 make -C linux-imx
 </pre>
@@ -14,6 +14,6 @@ sudo tar -C /opt -xf gcc-arm-10.3-2021.07-x86_64-aarch64-none-linux-gnu.tar.xz
 * Set environment variables:
 <pre>
 export ARCH=arm64
-export CROSS_COMPILE=/opt/gcc-arm-10.3-2021.07-x86_64-aarch64-none-linux-gnu/bin/aarch64-linux-gnu-
+export CROSS_COMPILE=/opt/gcc-arm-10.3-2021.07-x86_64-aarch64-none-linux-gnu/bin/aarch64-none-linux-gnu-
 </pre>

@@ -1,43 +1,14 @@
-# Quick Start Guide
+# Developer snapshot
+# Please do not try this at home

-Supported CompuLab machines:
-* `mcm-imx8m-mini`
-* `ucm-imx8m-mini`
+export COMPULAB_MACHINE=ucm-imx8m-mini
+export LREPO=imx_5.15.32-2.0.0-compulab.xml
+export CLB_RELEASE=rel_imx_5.15.32-2.0.0-experimental

-# 1 Setup environment
-## 1.1 Prepare NXP BSP
-```
-repo init -u git://source.codeaurora.org/external/imx/imx-manifest.git -b imx-linux-hardknott -m imx-5.10.35-2.0.0.xml
-```
-## 1.2 Download CompuLab meta layer
-```
-wget --directory-prefix .repo/manifests https://raw.githubusercontent.com/compulab-yokneam/meta-bsp-imx8mm/rel_imx_5.10.35_2.0.0-stable/scripts/imx-5.10.35_2.0.0_compulab.xml
-```
-## 1.3 Get entire BSP tree
-```
-repo init -m imx-5.10.35_2.0.0_compulab.xml
+repo init -u git://source.codeaurora.org/external/imx/imx-manifest.git -b imx-linux-kirkstone -m imx-5.15.32-2.0.0.xml
+
+mkdir -p .repo/local_manifests
+wget --directory-prefix .repo/local_manifests https://raw.githubusercontent.com/compulab-yokneam/meta-bsp-imx8mm/${CLB_RELEASE}/scripts/${LREPO}
 repo sync
-```

-# 2 Build
-## 2.1 Define COMPULAB_MACHINE environment variable
-|Machine|Command Line|
-|---|---|
-|mcm-imx8m-mini|```export COMPULAB_MACHINE=mcm-imx8m-mini```
-|ucm-imx8m-mini|```export COMPULAB_MACHINE=ucm-imx8m-mini```

-## 2.2 Run CompuLab Linux Yocto Project setup
-|NOTE|Refer to the [NXP Readme](https://source.codeaurora.org/external/imx/meta-imx/tree/README?h=hardknott-5.10.35-2.0.0) for details about how to select a correct backend & distro.|
-|---|---|
-```
-MACHINE=${COMPULAB_MACHINE} DISTRO=fsl-imx-xwayland source compulab-setup-env -b build
-```
-## 2.3 Build image
-```
-bitbake -k compulab-ucm-imx8m-mini
-```
-
-# 3 Precompiled images
-|Machine|Image|
-|---|---|
-|ucm-imx8m-mini|[compulab-ucm-imx8m-mini-ucm-imx8m-mini-YYYYMMDDhhmmss.rootfs.wic.bz2](https://drive.google.com/file/d/1PLSpK6_F1oTnSQqcTwHmpUboF7tbKLAv/view?usp=sharing)
@@ -9,15 +9,16 @@ BBFILE_COLLECTIONS += "compulab-bsp-imx8mm"
 BBFILE_PATTERN_compulab-bsp-imx8mm := "^${LAYERDIR}/"
 BBFILE_PRIORITY_compulab-bsp-imx8mm = "9"

+BBMASK += "meta-compulab/recipes-bsp"
 BBMASK += "meta-compulab/recipes-xfce"
 BBMASK += "meta-compulab/recipes-kernel"
 BBMASK += "meta-compulab/recipes-graphics"
 BBMASK += ".*boundary.*"

 CORE_IMAGE_EXTRA_INSTALL += " kernel-modules "
-CORE_IMAGE_EXTRA_INSTALL += "${@bb.utils.contains('DISTRO_CODENAME', 'dunfell', 'firmware-imx-sdma-imx7d', 'firmware-imx-sdma', d)}"
+CORE_IMAGE_EXTRA_INSTALL += " firmware-imx-sdma-imx7d "

 HOSTTOOLS += " git-lfs "
 HOSTTOOLS += " bison "

-LAYERSERIES_COMPAT_compulab-bsp-imx8mm = "sumo thud warrior zeus dunfell hardknott"
+LAYERSERIES_COMPAT_compulab-bsp-imx8mm = "kirkstone"
@@ -1,12 +1,15 @@
-MACHINEOVERRIDES =. "mx8:mx8m:mx8mm:"
+MACHINEOVERRIDES =. "imx-boot-container:mx8:mx8m:mx8mm:compulab-mx8mm:"

 SOC_DEFAULT_WKS_FILE = "imx-imx-boot-bootpart.wks.in"

 require conf/machine/include/imx-base.inc
-require conf/machine/include/tune-cortexa53.inc
+require conf/machine/include/arm/armv8a/tune-cortexa53.inc

 MACHINE_FEATURES += " pci wifi bluetooth "

+IMX_DEFAULT_BOOTLOADER:use-mainline-bsp = "u-boot-compulab"
+IMX_DEFAULT_BOOTLOADER:use-nxp-bsp = "u-boot-compulab"
+
 SPL_BINARY = "spl/u-boot-spl.bin"

 # Set DDR FIRMWARE
@@ -27,24 +30,36 @@ UBOOT_SUFFIX = "bin"
 UBOOT_MAKE_TARGET = ""
 IMX_BOOT_SEEK = "33"

+MACHINE_FIRMWARE:append = " firmware-cypress linux-firmware-ax200"
+
+MACHINE_FIRMWARE:remove = "linux-firmware-ath10k"
+
+DEFAULTTUNE:mx8mm-nxp-bsp = "aarch64"
+
+# PLATFORM_FLAVOR = "mx8mmevk"
+# PLATFORM_FLAVOR:ucm-imx8m-mini = "mx8mmevk"
+# PLATFORM_FLAVOR:mcm-imx8m-mini = "mx8mmevk"
+# PLATFORM_FLAVOR:iot-gate-imx8 = "mx8mmevk"
+# Optee parameters
 OPTEE_BIN_EXT = "8mm"
+OPTEE_PLATFORM_FLAVOR = "mx8mm_cl_iot_gate"
+PLATFORM_FLAVOR:iot-gate-imx8 = "${OPTEE_PLATFORM_FLAVOR}"
+PLATFORM_FLAVOR:mcm-imx8m-mini = "${OPTEE_PLATFORM_FLAVOR}"
+PLATFORM_FLAVOR:ucm-imx8m-mini = "${OPTEE_PLATFORM_FLAVOR}"
+TEE_LOAD_ADDR = "0x56000000"

-MACHINE_FIRMWARE_append = " firmware-cypress linux-firmware-ax200"
-
-MACHINE_FIRMWARE_remove = "linux-firmware-ath10k"
-
-DEFAULTTUNE_mx8mm = "aarch64"
-
-PLATFORM_FLAVOR = "mx8mmevk"
-PLATFORM_FLAVOR_ucm-imx8m-mini = "mx8mmevk"
-PLATFORM_FLAVOR_mcm-imx8m-mini = "mx8mmevk"
-PLATFORM_FLAVOR_iot-gate-imx8 = "mx8mmevk"
 ATF_MACHINE_NAME = "bl31-imx8mm.bin"
 PLATFORM = "imx8mm"
 SOC_TARGET = "iMX8MM"
+IMX_BOOT_SOC_TARGET = "iMX8MM"

-IMAGE_INSTALL_append = " \
+IMAGE_INSTALL:append = " \
 	kernel-image \
 	kernel-modules \
 	kernel-devicetree \
 "
+
+PREFERRED_PROVIDER_virtual/kernel:compulab-mx8mm = "linux-compulab"
+PREFERRED_PROVIDER_virtual/bootloader:compulab-mx8mm = "u-boot-compulab"
+PREFERRED_PROVIDER_linux-imx-mfgtool:compulab-mx8mm = "linux-compulab-mfgtool"
+PREFERRED_PROVIDER_linux-compulab-mfgtool:compulab-mx8mm = "linux-compulab-mfgtool"
@@ -9,6 +9,11 @@ require compulab-imx8mm.inc
 KERNEL_DEVICETREE = "compulab/ucm-imx8m-mini.dtb "
 KERNEL_DEVICETREE += "compulab/sb-iotgimx8.dtb "
 KERNEL_DEVICETREE += "compulab/sb-iotgimx8-can.dtb "
+KERNEL_DEVICETREE += "compulab/sb-iotgimx8-ied.dtb "
+KERNEL_DEVICETREE += "compulab/sb-iotgimx8-ied-m4.dtb "
+KERNEL_DEVICETREE += "compulab/sb-iotgimx8-poed.dtb "
+KERNEL_DEVICETREE += "compulab/sb-iotgimx8-poedv2.dtb "
+KERNEL_DEVICETREE += "compulab/sb-iotgimx8-ied-wakeup.dtb "

 UBOOT_CONFIG ??= "sd"
 UBOOT_CONFIG[sd] = "iot-gate-imx8_defconfig,sdcard"
@@ -16,3 +21,15 @@ UBOOT_CONFIG[mfgtool] = "iot-gate-imx8_defconfig"

 # Set u-boot DTB
 UBOOT_DTB_NAME = "iot-gate-imx8.dtb"
+
+# Prefered components
+# PREFERRED_PROVIDER_virtual/kernel_mx8mm = "linux-compulab"
+# PREFERRED_PROVIDER_virtual/bootloader_mx8mm = "u-boot-compulab"
+
+# Block recipes
+BBMASK += "meta-compulab/recipes-bsp/u-boot"
+
+# Optee parameters
+OPTEE_PLATFORM_FLAVOR = "mx8mm_cl_iot_gate"
+PLATFORM_FLAVOR:iot-gate-imx8 = "${OPTEE_PLATFORM_FLAVOR}"
+TEE_LOAD_ADDR = "0x56000000"
@@ -17,5 +17,5 @@ UBOOT_CONFIG[mfgtool] = "ucm-imx8m-mini_defconfig"
 # Set u-boot DTB
 UBOOT_DTB_NAME = "ucm-imx8m-mini.dtb"

-CL_RELEASE = '2.2.1'
+CL_RELEASE = '2.2'
 IMAGE_LINK_NAME = "${MACHINE}"
@@ -19,7 +19,7 @@ SRC_URI = "git://chromium.googlesource.com/chromiumos/third_party/broadcom;proto

 FILES_${PN} = "/usr/bin/*"

-do_install_append() {
+do_install:append() {
 	install -d ${D}/usr/bin
 	install -m 755 brcm_patchram_plus ${D}/usr/bin
 }
@@ -1,7 +0,0 @@
-FILESEXTRAPATHS_prepend := "${THISDIR}/files:"
-
-SRC_URI_append = " \
-	file://bt-start \
-"
-
-RDEPENDS_${PN} = "bash brcm-patchram firmware-imx-brcm"
@@ -1,13 +1,13 @@
 BB_STRICT_CHECKSUM = "0"

-SRC_URI_append += " \
+SRC_URI:append = " \
    https://github.com/compulab-yokneam/bin/raw/master/rootfs/lib/firmware/brcm/480-0081.tar.bz2;protocol=https;md5sum=c6a3119dec228a6fb65642be931ee6aa;sha256sum=e5755109f263a70738f59869704351a15c846a9a3963236ba9742eb4e0e67052 \
 "

-do_install_append () {
+do_install:append () {
    cp -rfv ${WORKDIR}/lib/firmware/brcm ${D}${base_libdir}/firmware/
 }

-FILES_${PN}-brcm += "${base_libdir}/firmware/brcm"
+FILES:${PN}-brcm += "${base_libdir}/firmware/brcm"
 PACKAGES =+ "${PN}-brcm"
 COMPATIBLE_MACHINE_ucm-imx8m-mini = "ucm-imx8m-mini"
@@ -1,6 +1,4 @@
-SRC_URI_append = " \
-	file://0001-imx8mm-Set-IMX_BOOT_UART_BASE-for-CompuLab-boards.patch \
-	file://0002-imx8mm-Assign-RDC_PDAP_UART4-to-D0.patch \
-	file://0003-imx8mm-Set-BL2_BASE-to-the-upper-egde-of-the-1G.patch \
-	file://0004-imx8mm-RDC-Remove-UART1-D0-restrictions.patch \
+SRC_URI:append = " \
+	file://0001-imx8mm-Assign-RDC_PDAP_UART4-to-D0.patch \
+	file://0002-iot-gate-imx8-RDC-Remove-UART2-D0-restrictions.patch \
 "
@@ -0,0 +1,26 @@
+From 48afff4126103326193042622273e036f3396d2c Mon Sep 17 00:00:00 2001
+From: Valentin Raevsky <valentin@compulab.co.il>
+Date: Wed, 8 Jul 2020 11:34:20 +0300
+Subject: [PATCH 1/2] imx8mm: Assign RDC_PDAP_UART4 to D0
+
+Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
+---
+ plat/imx/imx8m/imx8mm/imx8mm_bl31_setup.c | 2 +-
+ 1 file changed, 1 insertion(+), 1 deletion(-)
+
+diff --git a/plat/imx/imx8m/imx8mm/imx8mm_bl31_setup.c b/plat/imx/imx8m/imx8mm/imx8mm_bl31_setup.c
+index f63b9fcad..a89c7f941 100644
+--- a/plat/imx/imx8m/imx8mm/imx8mm_bl31_setup.c
+++ b/plat/imx/imx8m/imx8mm/imx8mm_bl31_setup.c
+@@ -58,7 +58,7 @@ static const struct imx_rdc_cfg rdc[] = {
+ 	RDC_MDAn(RDC_MDA_M4, DID1),
+ 
+ 	/* peripherals domain permission */
+-	RDC_PDAPn(RDC_PDAP_UART4, D1R | D1W),
+	RDC_PDAPn(RDC_PDAP_UART4, D0R | D0W),
+ 	RDC_PDAPn(RDC_PDAP_UART2, D0R | D0W),
+ 	RDC_PDAPn(RDC_PDAP_UART1, D0R | D0W),
+ 
+-- 
+2.11.0
+
@@ -0,0 +1,25 @@
+From 3d785a514a3c9251c9db6b4f575153311a848a6c Mon Sep 17 00:00:00 2001
+From: Uri Mashiach <uri.mashiach@compulab.co.il>
+Date: Wed, 4 May 2022 11:03:18 +0300
+Subject: [PATCH 2/2] iot-gate-imx8: RDC: Remove UART2 D0 restrictions
+
+Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
+---
+ plat/imx/imx8m/imx8mm/imx8mm_bl31_setup.c | 1 -
+ 1 file changed, 1 deletion(-)
+
+diff --git a/plat/imx/imx8m/imx8mm/imx8mm_bl31_setup.c b/plat/imx/imx8m/imx8mm/imx8mm_bl31_setup.c
+index a89c7f941..c7bfd3f9e 100644
+--- a/plat/imx/imx8m/imx8mm/imx8mm_bl31_setup.c
+++ b/plat/imx/imx8m/imx8mm/imx8mm_bl31_setup.c
+@@ -59,7 +59,6 @@ static const struct imx_rdc_cfg rdc[] = {
+ 
+ 	/* peripherals domain permission */
+ 	RDC_PDAPn(RDC_PDAP_UART4, D0R | D0W),
+-	RDC_PDAPn(RDC_PDAP_UART2, D0R | D0W),
+ 	RDC_PDAPn(RDC_PDAP_UART1, D0R | D0W),
+ 
+ 	/* memory region */
+-- 
+2.11.0
+
@@ -0,0 +1,11 @@
+FILESEXTRAPATHS:prepend := "${THISDIR}/compulab/imx8mm:"
+
+require compulab/imx8mm.inc
+
+ATF_PLATFORM = "imx8mm"
+
+EXTRA_OEMAKE += "\
+    IMX_BOOT_UART_BASE=0x30880000 \
+    BL32_BASE=${TEE_LOAD_ADDR} \
+    BL32_SIZE=0x2000000 \
+"
@@ -1,3 +1,3 @@
-FILESEXTRAPATHS_prepend := "${THISDIR}/compulab/imx8mm:"
+FILESEXTRAPATHS:prepend := "${THISDIR}/compulab/imx8mm:"

 include compulab/imx8mm.inc
@@ -1,12 +1,12 @@
 do_compile_preppend () {
    make_file=${S}/iMX8M/soc.mak
    if [ -e ${make_file} ]; then
-        sed -i "s/dtbs = .*dtb/dtbs = ${UBOOT_DTB_NAME}/g" ${make_file}
-	sed -i "s/\(^TEE_LOAD_ADDR \).*/\1= 0x7e000000/g" ${make_file}
+        sed -i "s/\(^dtbs \).*/\1= ${UBOOT_DTB_NAME}/g" ${make_file}
+	sed -i "s/\(^TEE_LOAD_ADDR \).*/\1= 0x56000000/g" ${make_file}
    fi
 }

-do_install_append () {
+do_install:append () {
        ln -fs ${BOOT_CONFIG_MACHINE}-${target} ${D}/boot/imx-boot
 }

@@ -1,7 +1,7 @@
 DESCRIPTION = "CompuLab release info."
 LICENSE = "MIT"

-do_install_append() {
+do_install:append() {
    for i in issue issue.net; do
 	sed -e "/^Compulab Release/d" -i ${D}/etc/$i
 	sed -e " 1 i $(date +"Compulab Release ${MACHINE} ${CL_RELEASE} %d %b %Y based on")" -i ${D}/etc/$i
@@ -3,4 +3,4 @@ LICENSE = "MIT"

 export IMAGE_LINK_NAME="${MACHINE}"

-require dynamic-layers/qt5-layer/recipes-fsl/images/fsl-image-qt5-validation-imx.bb
+#require dynamic-layers/qt6-layer/recipes-fsl/images/imx-image-full.bb
@@ -1,6 +1,6 @@
-FILESEXTRAPATHS_prepend := "${THISDIR}/${PN}:"
+FILESEXTRAPATHS:prepend := "${THISDIR}/${PN}:"

-do_compile_prepend() {
+do_compile:prepend() {
 	BOOTLOADER=$(basename $(ls ${WORKDIR}/recipe-sysroot/boot/imx-boot-* | head -1))
 	sed -i "s|##BOOTLOADER##|${BOOTLOADER}|" ${WORKDIR}/boot.script
 }
@@ -1,4 +1,5 @@
-SRC_URI_append = " \
+
+SRC_URI:append = " \
 	file://0001-ucm-imx8m-mini-Add-basic-support.patch \
 	file://0002-ucm-imx8m-mini-update-CPU-model-printed-parameters.patch \
 	file://0003-ucm-imx8m-mini-Fix-KConfig-warning.patch \
@@ -50,58 +51,81 @@ SRC_URI_append = " \
 	file://0049-mcm-imx8m-mini-dts-Enable-usbotg2-in-host-mode.patch \
 	file://0050-mcm-imx8m-mini-config-Remove-unused-stuff.patch \
 	file://0051-mcm-imx8m-mini-Remove-dram_init_banksize-and-get_eff.patch \
-	file://0052-imx8m-soc-Don-t-reduce-the-memory-amount-by-the-opte.patch \
-	file://0053-mcm-imx8m-mini-Move-tcm-to-plat-imx8mm.patch \
-	file://0054-mcm-imx8m-mini-Refactor-spl-code.patch \
-	file://0055-ucm-imx8m-mini-Refactor-the-code-for-2020.04.patch \
-	file://0056-cpl-imx8m-mini-Set-LOCALVERSION-intead-of-EXTRAVERSI.patch \
-	file://0057-cpl-imx8m-mini-Refactor-.h-configs.patch \
-	file://0058-cpl-imx8m-mini-Refactor-.dts.patch \
-	file://0059-iot-gate-imx8-Add-basic-support.patch \
-	file://0060-mcm-imx8m-mini-config-Update-env-size-offest.patch \
-	file://0061-imx8m-mini-env-config-Update-size-offset-value.patch \
-	file://0062-imx8-eeprom-Move-to-the-imx8-platform-independent-fo.patch \
-	file://0063-imx8-eeprom-Remove-duplicated-code.patch \
-	file://0064-imx8mm-plat-Add-the-common-board-file-for-imx8mm-SoC.patch \
-	file://0065-imx8m-mini-Refactor-the-usdhc2.patch \
-	file://0066-mcm-imx8m-mini-reset-Refactor-the-reset.patch \
-	file://0067-imx8m-mini-ddr-Change-the-memory-presets-order.patch \
-	file://0068-imx8m-mini-env-Fix-getopt_long-parameters-string.patch \
-	file://0069-ucm-imx8m-mini-Fix-reset.patch \
-	file://0070-imx8m-mini-spl-Add-__weak-board_fit_config_name_matc.patch \
-	file://0071-mcm-imx8m-mini-spl-Add-board_fit_config_name_match.patch \
-	file://0072-imx8m-mini-u-boot-Add-__weak-uboot_board_private_ini.patch \
-	file://0073-mcm-imx8m-mini-u-boot-Add-uboot_board_private_init.patch \
-	file://0074-Add-ddr_init-return-handling.patch \
-	file://0075-spl-Enable-Kingston-DRAM-support.patch \
-	file://0076-Add-show_suite-function.patch \
-	file://0077-Clean-debug-printout.patch \
-	file://0078-imx8m-ddr-Add-Nanya-2G-2400-MTS-support.patch \
-	file://0079-ucm-imx8m-mini-Enable-status-LED-and-cmd-led.patch \
-	file://0080-mcm-and-ucm-Enable-status-LED-for-both-platforms.patch \
-	file://0081-Enable-env-address-export-via-FDT.patch \
-	file://0082-fw_utils-Enable-actual-env-address-readout.patch \
-	file://0083-SPL-Disable-fake-memsize-report.patch \
-	file://0084-fdt-Add-export-SoM-data-via-FDT.patch \
-	file://0085-board-minor-cleaninig.patch \
-	file://0086-rtc-Disable-bus-when-powered-from-battery.patch \
-	file://0087-fdt-Add-export-of-base-board-data-via-FDT.patch \
-	file://0088-spl-ddr-Enable-DDR-ID-0x1060008.patch \
-	file://0089-drivers-video-Add-startek-ili9881c-panel-driver.patch \
-	file://0090-cpl-imx8m-mini-Enable-startek-ili9881c-panel-support.patch \
-	file://0091-cm-imx8m-mini-config-Enable-startek-ili9881c.patch \
-	file://0092-Migration-to-5.10.35.patch \
-	file://0093-Fix-enable_cache.patch \
-	file://0094-Fix-mmc_autodetect.patch \
-	file://0095-config-Enable-video.patch \
-	file://0096-readout-some-cleannig.patch \
-	file://0097-mmc-Fix-mmc_switch-workflow-issue.patch \
-	file://0098-defconfig-Break-down-to-common-and-specific-parts.patch \
-	file://0099-spl-lpddr-training-size-optimisation.patch \
-	file://0100-spl-Add-SDP-support.patch \
-	file://0101-spl-Enable-Samsung-4G-DRAM-0x01061010.patch \
-	file://0102-Enable-DDR-Alliance-1G-0x01050008.patch \
-	file://0103-make-Add-wrapper-for-compound-config.patch \
-	file://0104-net-Enable-phy-Realtek-RTL8211E.patch \
-	file://0105-LOCALVERSION-2.2.1-1.1.1.patch \
+	file://0052-mcm-imx8m-mini-Move-tcm-to-plat-imx8mm.patch \
+	file://0053-mcm-imx8m-mini-Refactor-spl-code.patch \
+	file://0054-ucm-imx8m-mini-Refactor-the-code-for-2020.04.patch \
+	file://0055-cpl-imx8m-mini-Set-LOCALVERSION-intead-of-EXTRAVERSI.patch \
+	file://0056-cpl-imx8m-mini-Refactor-.h-configs.patch \
+	file://0057-cpl-imx8m-mini-Refactor-.dts.patch \
+	file://0058-iot-gate-imx8-Add-basic-support.patch \
+	file://0059-mcm-imx8m-mini-config-Update-env-size-offest.patch \
+	file://0060-imx8m-mini-env-config-Update-size-offset-value.patch \
+	file://0061-imx8-eeprom-Move-to-the-imx8-platform-independent-fo.patch \
+	file://0062-imx8-eeprom-Remove-duplicated-code.patch \
+	file://0063-imx8mm-plat-Add-the-common-board-file-for-imx8mm-SoC.patch \
+	file://0064-imx8m-mini-Refactor-the-usdhc2.patch \
+	file://0065-mcm-imx8m-mini-reset-Refactor-the-reset.patch \
+	file://0066-imx8m-mini-ddr-Change-the-memory-presets-order.patch \
+	file://0067-imx8m-mini-env-Fix-getopt_long-parameters-string.patch \
+	file://0068-ucm-imx8m-mini-Fix-reset.patch \
+	file://0069-imx8m-mini-spl-Add-__weak-board_fit_config_name_matc.patch \
+	file://0070-mcm-imx8m-mini-spl-Add-board_fit_config_name_match.patch \
+	file://0071-imx8m-mini-u-boot-Add-__weak-uboot_board_private_ini.patch \
+	file://0072-mcm-imx8m-mini-u-boot-Add-uboot_board_private_init.patch \
+	file://0073-Add-ddr_init-return-handling.patch \
+	file://0074-spl-Enable-Kingston-DRAM-support.patch \
+	file://0075-Add-show_suite-function.patch \
+	file://0076-Clean-debug-printout.patch \
+	file://0077-imx8m-ddr-Add-Nanya-2G-2400-MTS-support.patch \
+	file://0078-ucm-imx8m-mini-Enable-status-LED-and-cmd-led.patch \
+	file://0079-mcm-and-ucm-Enable-status-LED-for-both-platforms.patch \
+	file://0080-Enable-env-address-export-via-FDT.patch \
+	file://0081-fw_utils-Enable-actual-env-address-readout.patch \
+	file://0082-SPL-Disable-fake-memsize-report.patch \
+	file://0083-fdt-Add-export-SoM-data-via-FDT.patch \
+	file://0084-board-minor-cleaninig.patch \
+	file://0085-rtc-Disable-bus-when-powered-from-battery.patch \
+	file://0086-fdt-Add-export-of-base-board-data-via-FDT.patch \
+	file://0087-spl-ddr-Enable-DDR-ID-0x1060008.patch \
+	file://0088-drivers-video-Add-startek-ili9881c-panel-driver.patch \
+	file://0089-cpl-imx8m-mini-Enable-startek-ili9881c-panel-support.patch \
+	file://0090-cm-imx8m-mini-config-Enable-startek-ili9881c.patch \
+	file://0091-Migration-to-5.10.35.patch \
+	file://0092-Fix-mmc_autodetect.patch \
+	file://0093-config-Enable-video.patch \
+	file://0094-mmc-Fix-mmc_switch-workflow-issue.patch \
+	file://0095-defconfig-Break-down-to-common-and-specific-parts.patch \
+	file://0096-spl-lpddr-training-size-optimisation.patch \
+	file://0097-spl-Add-SDP-support.patch \
+	file://0098-spl-Enable-Samsung-4G-DRAM-0x01061010.patch \
+	file://0099-Enable-DDR-Alliance-1G-0x01050008.patch \
+	file://0100-make-Add-wrapper-for-compound-config.patch \
+	file://0102-defconfig-Enable-EFI_LOADER.patch \
+	file://0103-core-Add-EPFNOSUPPORT-handeler.patch \
+	file://0104-cpl-imx8m-mini-dts-remove-unrelevant-sections.patch \
+	file://0105-iot-gate-imx8-remove-driver-reset-functions.patch \
+	file://0106-iot-gate-imx8-dts-set-MMC1-voltage-to-1.8V.patch \
+	file://0107-iot-gate-imx8-usb-VBUS-enable-fix.patch \
+	file://0108-imx8mm-enable-global-functions-implementation-in-sub.patch \
+	file://0109-iot-gate-imx8-RS485-232-selection.patch \
+	file://0110-iot-gate-imx8-add-extension-board-support.patch \
+	file://0111-iot-gate-imx8-update-boot-sequence.patch \
+	file://0112-iot-gate-imx8-prevent-network-interfaces-rename.patch \
+	file://0113-iot-gate-imx8-update-prompt.patch \
+	file://0114-imx8mm-enable-prompt-update-in-sub-projects.patch \
+	file://0115-iot-gate-imx8-hide-temperature-message.patch \
+	file://0116-iot-gate-imx8-fix-UART1-mode-GPIO.patch \
+	file://0117-iot-gate-imx8-add-support-for-the-IE-TPM-module.patch \
+	file://0118-iot-gate-imx8-add-support-for-the-IE-POE-extension-b.patch \
+	file://0119-iot-gate-imx8-update-support-for-the-IE-TPM-module.patch \
+	file://0120-iot-gate-imx8-add-support-for-the-IE-CL420-module.patch \
+	file://0121-iot-gate-imx8-add-support-for-the-POEv2-module.patch \
+	file://0122-iot-gate-imx8-enable-USB-to-Ethernet-driver-SMSC-LAN.patch \
+	file://0123-cmd-eeprom-fix-disregarding-of-the-i2c_bus-parameter.patch \
+	file://0124-Enable-SoC-info-export-via-fdt.patch \
+	file://0125-imx8mm-net-enable-phy-Realtek-RTL8211E.patch \
+	file://0126-iot-gate-imx8-release-2020.04-iot-gate-imx8-3.0.patch \
 "
+ 
+#	For U-Boot build outside of Yocto
+#	file://0101-compulab-imx8mm-Add-binman-support.patch
@@ -1,34 +1,34 @@
-From 22c3acad098a8c75bd8791eb1ae0e370c0b2984a Mon Sep 17 00:00:00 2001
+From a79e947a2a87a687a2cd9fb6e43e3c5d8d29b262 Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Sun, 18 Jul 2021 23:23:16 +0300
-Subject: [PATCH 01/91] ucm-imx8m-mini: Add basic support
+Subject: [PATCH 001/126] ucm-imx8m-mini: Add basic support

 Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 ---
- arch/arm/dts/Makefile                         |    2 +
- arch/arm/dts/ucm-imx8m-mini.dts               |  452 ++++
- arch/arm/mach-imx/imx8m/Kconfig               |    8 +
- board/compulab/common/Makefile                |    1 +
- board/compulab/common/eeprom.c                |    4 +-
- board/compulab/common/mmc.c                   |   50 +
- board/compulab/common/pfuze.c                 |  174 ++
- board/compulab/common/pfuze.h                 |   19 +
- board/compulab/common/pfuze_dm.c              |   89 +
- board/compulab/common/tcpc.h                  |  454 ++++
- board/compulab/ucm-imx8m-mini/Kconfig         |   30 +
- board/compulab/ucm-imx8m-mini/Makefile        |   16 +
- board/compulab/ucm-imx8m-mini/ddr/Makefile    |   11 +
- board/compulab/ucm-imx8m-mini/ddr/ddr.h       |   59 +
- board/compulab/ucm-imx8m-mini/ddr/ddr_init.c  |  255 +++
- .../ucm-imx8m-mini/ddr/ddrphy_train.c         | 1044 +++++++++
- board/compulab/ucm-imx8m-mini/ddr/helper.c    |  103 +
- .../ddr/wait_ddrphy_training_complete.c       |  103 +
- board/compulab/ucm-imx8m-mini/lpddr4_timing.c | 1980 +++++++++++++++++
- board/compulab/ucm-imx8m-mini/spl.c           |  258 +++
- .../compulab/ucm-imx8m-mini/ucm-imx8m-mini.c  |  734 ++++++
- configs/ucm-imx8m-mini_defconfig              |   56 +
- include/configs/ucm-imx8m-mini.h              |  361 +++
- 23 files changed, 6261 insertions(+), 2 deletions(-)
+ arch/arm/dts/Makefile                              |    2 +
+ arch/arm/dts/ucm-imx8m-mini.dts                    |  452 +++++
+ arch/arm/mach-imx/imx8m/Kconfig                    |    8 +
+ board/compulab/common/Makefile                     |    1 +
+ board/compulab/common/eeprom.c                     |    4 +-
+ board/compulab/common/mmc.c                        |   51 +
+ board/compulab/common/pfuze.c                      |  174 ++
+ board/compulab/common/pfuze.h                      |   19 +
+ board/compulab/common/pfuze_dm.c                   |   89 +
+ board/compulab/common/tcpc.h                       |  454 +++++
+ board/compulab/ucm-imx8m-mini/Kconfig              |   30 +
+ board/compulab/ucm-imx8m-mini/Makefile             |   16 +
+ board/compulab/ucm-imx8m-mini/ddr/Makefile         |   11 +
+ board/compulab/ucm-imx8m-mini/ddr/ddr.h            |   59 +
+ board/compulab/ucm-imx8m-mini/ddr/ddr_init.c       |  255 +++
+ board/compulab/ucm-imx8m-mini/ddr/ddrphy_train.c   | 1044 +++++++++++
+ board/compulab/ucm-imx8m-mini/ddr/helper.c         |  103 +
+ .../ddr/wait_ddrphy_training_complete.c            |  103 +
+ board/compulab/ucm-imx8m-mini/lpddr4_timing.c      | 1980 ++++++++++++++++++++
+ board/compulab/ucm-imx8m-mini/spl.c                |  258 +++
+ board/compulab/ucm-imx8m-mini/ucm-imx8m-mini.c     |  734 ++++++++
+ configs/ucm-imx8m-mini_defconfig                   |   56 +
+ include/configs/ucm-imx8m-mini.h                   |  361 ++++
+ 23 files changed, 6262 insertions(+), 2 deletions(-)
 create mode 100644 arch/arm/dts/ucm-imx8m-mini.dts
 create mode 100644 board/compulab/common/mmc.c
 create mode 100644 board/compulab/common/pfuze.c
@@ -50,10 +50,10 @@ Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 create mode 100644 include/configs/ucm-imx8m-mini.h

 diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
-index aa0c6a75c3..2b81a2bc62 100644
+index 24a387fb60..c31d483784 100644
 --- a/arch/arm/dts/Makefile
 +++ b/arch/arm/dts/Makefile
-@@ -890,6 +890,8 @@ dtb-$(CONFIG_RCAR_GEN2) += \
+@@ -898,6 +898,8 @@ dtb-$(CONFIG_RCAR_GEN2) += \
 	r8a7794-alt-u-boot.dtb \
 	r8a7794-silk-u-boot.dtb
 
@@ -521,10 +521,10 @@ index 0000000000..112345b6a3
 +	status = "disabled";
 +};
 diff --git a/arch/arm/mach-imx/imx8m/Kconfig b/arch/arm/mach-imx/imx8m/Kconfig
-index 9e5b6d7ffa..d4c41ba1aa 100644
+index 245b085499..4930b9bee6 100644
 --- a/arch/arm/mach-imx/imx8m/Kconfig
 +++ b/arch/arm/mach-imx/imx8m/Kconfig
-@@ -201,6 +201,13 @@ config TARGET_PHYCORE_IMX8MP
+@@ -259,6 +259,13 @@ config TARGET_PHYCORE_IMX8MP
 	select IMX8MP
         select SUPPORT_SPL
 	select IMX8M_LPDDR4
@@ -538,7 +538,7 @@ index 9e5b6d7ffa..d4c41ba1aa 100644
 endchoice
 
 source "board/freescale/imx8mq_evk/Kconfig"
-@@ -217,5 +224,6 @@ source "board/beacon/imx8mm/Kconfig"
+@@ -276,5 +283,6 @@ source "board/beacon/imx8mm/Kconfig"
 source "board/beacon/imx8mn/Kconfig"
 source "board/phytec/phycore_imx8mm/Kconfig"
 source "board/phytec/phycore_imx8mp/Kconfig"
@@ -582,10 +582,10 @@ index 5206cf5c0a..e23dd68437 100644
 	uint offset;
 diff --git a/board/compulab/common/mmc.c b/board/compulab/common/mmc.c
 new file mode 100644
-index 0000000000..9fc3e68728
+index 0000000000..52b15ab5f3
 --- /dev/null
 +++ b/board/compulab/common/mmc.c
-@@ -0,0 +1,50 @@
+@@ -0,0 +1,51 @@
 +/*
 + * Copyright (C) 2016 Freescale Semiconductor, Inc.
 + * Copyright 2018 NXP
@@ -598,6 +598,7 @@ index 0000000000..9fc3e68728
 +#include <asm/io.h>
 +#include <stdbool.h>
 +#include <mmc.h>
+#include <command.h>
 +
 +static int check_mmc_autodetect(void)
 +{
@@ -6485,5 +6486,5 @@ index 0000000000..1605ab7281
 +#endif
 +#endif
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From fd167e54036b16013eecd9504fa392734f725fb0 Mon Sep 17 00:00:00 2001
+From aa605296da62f4b44932c7d8eedbc95518352cec Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Tue, 26 May 2020 20:55:00 +0300
-Subject: [PATCH 02/91] ucm-imx8m-mini: update CPU/model printed parameters
+Subject: [PATCH 002/126] ucm-imx8m-mini: update CPU/model printed parameters

 Update the startup messages of the CPU and model parameters

@@ -24,5 +24,5 @@ index 112345b6a3..899899c1c6 100644
 
 	chosen {
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 5dabb2f3f0d1814c111ff4c6edd2a88360b88948 Mon Sep 17 00:00:00 2001
+From 665396af251f6eec00d0ece435f120a75ea3e621 Mon Sep 17 00:00:00 2001
 From: Uri Mashiach <uri.mashiach@compulab.co.il>
 Date: Wed, 13 Feb 2019 08:56:03 +0200
-Subject: [PATCH 03/91] ucm-imx8m-mini: Fix KConfig warning
+Subject: [PATCH 003/126] ucm-imx8m-mini: Fix KConfig warning

 The following compilation warning is generated:
 choice value used outside its choice group
@@ -84,5 +84,5 @@ index 6d9cccdbcb..34f7683d2d 100644
 	ddr_init();
 #endif
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 4c4365f284eee7ed73c65dd3f1cb9fbfa65ef095 Mon Sep 17 00:00:00 2001
+From c826389773619e592df6ccc852cb636b61d935d0 Mon Sep 17 00:00:00 2001
 From: Uri Mashiach <uri.mashiach@compulab.co.il>
 Date: Wed, 13 Feb 2019 15:04:59 +0200
-Subject: [PATCH 04/91] ucm-imx8m-mini: enable status LED
+Subject: [PATCH 004/126] ucm-imx8m-mini: enable status LED

 Use the status LED feature to turn on the status LED.

@@ -35,5 +35,5 @@ index 2212e76acb..36cfe1b2e1 100644
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH=y
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 20aa60bc1225baa35bcc2660351d2a1359fd49ad Mon Sep 17 00:00:00 2001
+From fcdfa92492c4104cfd01ed1fe9ac77b8fd204b1d Mon Sep 17 00:00:00 2001
 From: Uri Mashiach <uri.mashiach@compulab.co.il>
 Date: Mon, 18 Sep 2017 19:49:32 +0300
-Subject: [PATCH 05/91] eeprom: layout: remove buf from the eeprom_field
+Subject: [PATCH 005/126] eeprom: layout: remove buf from the eeprom_field
 structure

 The layout structure contains a pointer to a buffer that contain the
@@ -17,10 +17,10 @@ pointer parameter to the field functions.

 Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
 ---
- board/compulab/common/eeprom.c | 150 +++++++++++++++++----------------
- common/eeprom/eeprom_field.c   |  73 ++++++++++------
- common/eeprom/eeprom_layout.c  |  21 ++---
- include/eeprom_field.h         |  31 ++++---
+ board/compulab/common/eeprom.c | 150 +++++++++++++++++++++--------------------
+ common/eeprom/eeprom_field.c   |  73 ++++++++++++--------
+ common/eeprom/eeprom_layout.c  |  21 +++---
+ include/eeprom_field.h         |  31 +++++----
 4 files changed, 149 insertions(+), 126 deletions(-)

 diff --git a/board/compulab/common/eeprom.c b/board/compulab/common/eeprom.c
@@ -603,5 +603,5 @@ index 05c0d14592..a13ca566af 100644
 
 #endif
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From ebfbf0ddfda20d3191ee5b0a1d7341cd68465b72 Mon Sep 17 00:00:00 2001
+From cbdfb5f0fea713cc69de29e75a05b36ce50b6931 Mon Sep 17 00:00:00 2001
 From: Uri Mashiach <uri.mashiach@compulab.co.il>
 Date: Tue, 19 Sep 2017 10:07:26 +0300
-Subject: [PATCH 06/91] eeprom: layout: add field functions read
+Subject: [PATCH 006/126] eeprom: layout: add field functions read

 Read option is missing in the EEPROM layout feature

@@ -11,9 +11,9 @@ provided buffer without manipulation.

 Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
 ---
- board/compulab/common/eeprom.c | 91 +++++++++++++++++-----------------
- common/eeprom/eeprom_field.c   | 22 ++++++++
- common/eeprom/eeprom_layout.c  | 37 ++++++++++++++
+ board/compulab/common/eeprom.c | 91 +++++++++++++++++++++---------------------
+ common/eeprom/eeprom_field.c   | 22 ++++++++++
+ common/eeprom/eeprom_layout.c  | 37 +++++++++++++++++
 include/eeprom_field.h         |  4 ++
 include/eeprom_layout.h        |  2 +
 5 files changed, 111 insertions(+), 45 deletions(-)
@@ -146,11 +146,10 @@ diff --git a/common/eeprom/eeprom_field.c b/common/eeprom/eeprom_field.c
 index 38827f1180..e588b0943f 100644
 --- a/common/eeprom/eeprom_field.c
 +++ b/common/eeprom/eeprom_field.c
-@@ -129,6 +129,28 @@ int eeprom_field_update_bin(struct eeprom_field *field, uchar *fbuf,
- 	return __eeprom_field_update_bin(field, fbuf, value, false);
+@@ -130,6 +130,28 @@ int eeprom_field_update_bin(struct eeprom_field *field, uchar *fbuf,
 }
 
-+/**
+ /**
 + * eeprom_field_read_bin() - Read field data in binary form
 + *
 + * @field:     an initialized field
@@ -172,18 +171,18 @@ index 38827f1180..e588b0943f 100644
 +	return 0;
 +}
 +
- /**
+/**
  * eeprom_field_update_reserved() - Update reserved field with new data in
  *				    binary form
+  *
 diff --git a/common/eeprom/eeprom_layout.c b/common/eeprom/eeprom_layout.c
 index 1fab8e4dca..cc6dd39e01 100644
 --- a/common/eeprom/eeprom_layout.c
 +++ b/common/eeprom/eeprom_layout.c
-@@ -95,6 +95,42 @@ static int eeprom_layout_update_field(struct eeprom_layout *layout,
- 	return -1;
+@@ -96,6 +96,42 @@ static int eeprom_layout_update_field(struct eeprom_layout *layout,
 }
 
-+/*
+ /*
 + * eeprom_layout_read_field() - read a single field from the layout data
 + * @layout:    A pointer to an existing struct layout.
 + * @field_name:        The name of the field to update.
@@ -219,9 +218,10 @@ index 1fab8e4dca..cc6dd39e01 100644
 +	return -1;
 +}
 +
- /*
+/*
  * eeprom_layout_setup() - setup layout struct with the layout data and
  *			   metadata as dictated by layout_version
+  * @layout:	A pointer to an existing struct layout.
@@ -116,4 +152,5 @@ void eeprom_layout_setup(struct eeprom_layout *layout, unsigned char *buf,
 	layout->data_size = buf_size;
 	layout->print = eeprom_layout_print;
@@ -262,5 +262,5 @@ index 730d963ab9..50e8ec1085 100644
 
 void eeprom_layout_setup(struct eeprom_layout *layout, unsigned char *buf,
 -- 
-2.17.1
+2.11.0

@@ -1,16 +1,16 @@
-From c4e09d71adf13ae781ed295c0667b5ce0a3a2b60 Mon Sep 17 00:00:00 2001
+From 42ee0d104b1ecc275269d401cfaad103863cc1e9 Mon Sep 17 00:00:00 2001
 From: Uri Mashiach <uri.mashiach@compulab.co.il>
 Date: Tue, 19 Sep 2017 10:47:25 +0300
-Subject: [PATCH 07/91] compulab: eeprom: layout: add read serial function
+Subject: [PATCH 007/126] compulab: eeprom: layout: add read serial function

 The function conver the CompuLab serial number format to tag_serialnr
 structure.

 Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
 ---
- board/compulab/common/eeprom.c | 67 ++++++++++++++++++++++++++--------
- common/eeprom/eeprom_field.c   | 21 +++++++++++
- include/eeprom_field.h         |  2 +
+ board/compulab/common/eeprom.c | 67 ++++++++++++++++++++++++++++++++----------
+ common/eeprom/eeprom_field.c   | 21 +++++++++++++
+ include/eeprom_field.h         |  2 ++
 3 files changed, 75 insertions(+), 15 deletions(-)

 diff --git a/board/compulab/common/eeprom.c b/board/compulab/common/eeprom.c
@@ -191,11 +191,10 @@ diff --git a/common/eeprom/eeprom_field.c b/common/eeprom/eeprom_field.c
 index e588b0943f..814dc4eb7a 100644
 --- a/common/eeprom/eeprom_field.c
 +++ b/common/eeprom/eeprom_field.c
-@@ -203,6 +203,27 @@ int eeprom_field_update_bin_rev(struct eeprom_field *field, uchar *fbuf,
- 	return __eeprom_field_update_bin(field, fbuf, value, true);
+@@ -204,6 +204,27 @@ int eeprom_field_update_bin_rev(struct eeprom_field *field, uchar *fbuf,
 }
 
-+/**
+ /**
 + * eeprom_field_read_rev() - Read reversed binary data
 + *
 + * @field:     an initialized field
@@ -216,9 +215,10 @@ index e588b0943f..814dc4eb7a 100644
 +	return 0;
 +}
 +
- /**
+/**
  * eeprom_field_print_mac_addr() - print a field which contains a mac address
  *
+  * Treat the field data as simple binary data, and print it formatted as a MAC
 diff --git a/include/eeprom_field.h b/include/eeprom_field.h
 index 6b6cd37229..311c49401a 100644
 --- a/include/eeprom_field.h
@@ -233,5 +233,5 @@ index 6b6cd37229..311c49401a 100644
 void eeprom_field_print_mac(const struct eeprom_field *field, uchar *fbuf);
 int eeprom_field_update_mac(struct eeprom_field *field, uchar *fbuf,
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 6ae3d093dda3585c0f82f8f044ae7fe542ad8e49 Mon Sep 17 00:00:00 2001
+From e7068f16b334d6c518401e30013074a0f88b1ab9 Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Tue, 26 May 2020 21:17:29 +0300
-Subject: [PATCH 08/91] compulab: integrate DM_I2C in EEPROM driver
+Subject: [PATCH 008/126] compulab: integrate DM_I2C in EEPROM driver

 CompuLab's EEPROM driver is enabled only for CONFIG_SYS_I2C.
 Update the  enabling condition of the driver to CONFIG_SYS_I2C or
@@ -41,5 +41,5 @@ index a9c0203b81..2628d4ab86 100644
 u32 cl_eeprom_get_board_rev(uint eeprom_bus);
 int cl_eeprom_get_product_name(uchar *buf, uint eeprom_bus);
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From a97a2cf1a2667ab13ecce0bc7c362c7b49008bf7 Mon Sep 17 00:00:00 2001
+From 41e820e4b705ab5400c78eb0e3ec4f1fc1a9bbc2 Mon Sep 17 00:00:00 2001
 From: Uri Mashiach <uri.mashiach@compulab.co.il>
 Date: Tue, 19 Feb 2019 18:48:29 +0200
-Subject: [PATCH 09/91] ucm-imx8m-mini: add support for eeprom layout comands
+Subject: [PATCH 009/126] ucm-imx8m-mini: add support for eeprom layout comands

 Add support for EEPROM and EEPROM layout commands for the
 UCM-iMX8M-Mini.
@@ -54,5 +54,5 @@ index 1605ab7281..f464ed822b 100644
 #ifndef CONFIG_SPL_BUILD
 #define CONFIG_CMD_USB
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 22c1aa3dd9a65033682e1bec93dad9f20a8d9ed5 Mon Sep 17 00:00:00 2001
+From 9da7a67ead6515dbead3bb5ebba3337711508982 Mon Sep 17 00:00:00 2001
 From: Uri Mashiach <uri.mashiach@compulab.co.il>
 Date: Tue, 19 Feb 2019 21:46:54 +0200
-Subject: [PATCH 10/91] mx8m-mini: set Ethernet MAC address environment
+Subject: [PATCH 010/126] mx8m-mini: set Ethernet MAC address environment

 If the environment variable "ethaddr" is empty:
 * Read the MAC address from the EEPROM.
@@ -9,7 +9,7 @@ If the environment variable "ethaddr" is empty:

 Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
 ---
- .../compulab/ucm-imx8m-mini/ucm-imx8m-mini.c  | 37 +++++++++++++++++++
+ board/compulab/ucm-imx8m-mini/ucm-imx8m-mini.c | 37 ++++++++++++++++++++++++++
 1 file changed, 37 insertions(+)

 diff --git a/board/compulab/ucm-imx8m-mini/ucm-imx8m-mini.c b/board/compulab/ucm-imx8m-mini/ucm-imx8m-mini.c
@@ -86,5 +86,5 @@ index ef5d1ffa55..80d9a5b8bd 100644
 }
 
 -- 
-2.17.1
+2.11.0

@@ -1,11 +1,11 @@
-From faf90f560f89ba9ebc0f418f15e9d170deba617d Mon Sep 17 00:00:00 2001
+From 9247cadb067e9dc9b05851dedde17942d1bf7b34 Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Wed, 20 Feb 2019 08:21:05 +0200
-Subject: [PATCH 11/91] ucm-imx8m-mini: config: Remove unused stuff
+Subject: [PATCH 011/126] ucm-imx8m-mini: config: Remove unused stuff

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
 ---
- include/configs/ucm-imx8m-mini.h | 53 --------------------------------
+ include/configs/ucm-imx8m-mini.h | 53 ----------------------------------------
 1 file changed, 53 deletions(-)

 diff --git a/include/configs/ucm-imx8m-mini.h b/include/configs/ucm-imx8m-mini.h
@@ -81,5 +81,5 @@ index f464ed822b..214dad40ed 100644
 
 #define CONFIG_MXC_OCOTP
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 039d1bfdc99917232adcc642e082af7a576b28f2 Mon Sep 17 00:00:00 2001
+From 266c4024565e18cf4b3aa0bc41fe37a01f8d8c08 Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Thu, 7 Mar 2019 14:17:42 +0200
-Subject: [PATCH 12/91] ucm-imx8m-mini: Enable uart4 for bluetooth
+Subject: [PATCH 012/126] ucm-imx8m-mini: Enable uart4 for bluetooth

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
 ---
@@ -62,5 +62,5 @@ index 899899c1c6..003cc857df 100644
 	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
 -- 
-2.17.1
+2.11.0

@@ -1,12 +1,12 @@
-From 191feb9ba6cd656f2f8c8c56749e204ca5aab4f6 Mon Sep 17 00:00:00 2001
+From 6bcfe6007bc66837010335c9048fc593677f68a2 Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Tue, 26 Mar 2019 10:36:45 +0200
-Subject: [PATCH 13/91] ucm-imx8m-mini: ddr: Validate new setting
+Subject: [PATCH 013/126] ucm-imx8m-mini: ddr: Validate new setting

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
 ---
- board/compulab/ucm-imx8m-mini/ddr/ddr_init.c  | 23 +++--
- .../ucm-imx8m-mini/ddr/ddrphy_train.c         | 96 +++++++++----------
+ board/compulab/ucm-imx8m-mini/ddr/ddr_init.c     | 23 +++---
+ board/compulab/ucm-imx8m-mini/ddr/ddrphy_train.c | 96 ++++++++++++------------
 2 files changed, 62 insertions(+), 57 deletions(-)

 diff --git a/board/compulab/ucm-imx8m-mini/ddr/ddr_init.c b/board/compulab/ucm-imx8m-mini/ddr/ddr_init.c
@@ -324,5 +324,5 @@ index 8116069dfb..e4577e0a21 100644
 +}
 \ No newline at end of file
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 25d672480dabfc27a2bc746dd75e6a30d8e117cc Mon Sep 17 00:00:00 2001
+From 76a3fdd109d7326b5ba48fb92752a6a188e2fda4 Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Wed, 27 Mar 2019 13:28:51 +0200
-Subject: [PATCH 14/91] ucm-imx8m-mini: defconfig: Disable CONFIG_NXP_TMU
+Subject: [PATCH 014/126] ucm-imx8m-mini: defconfig: Disable CONFIG_NXP_TMU

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
 ---
@@ -21,5 +21,5 @@ index b4a9975b33..75531acb20 100644
 CONFIG_DM_USB=y
 CONFIG_USB_EHCI_HCD=y
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From bcba8667218c69dc9ed5a8894094dc0ab38966c4 Mon Sep 17 00:00:00 2001
+From 45fae1b2de5c218f33a822aedd8b58dfa74cc0f4 Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Mon, 22 Apr 2019 12:06:29 +0300
-Subject: [PATCH 15/91] ucm-imx8m-mini: config : Update h-file
+Subject: [PATCH 015/126] ucm-imx8m-mini: config : Update h-file

 1) Add a missing include
 2) Remove duplications
@@ -46,5 +46,5 @@ index 214dad40ed..046dc243bc 100644
 
 #define CONFIG_CMD_USB_MASS_STORAGE
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From e3456703938fdcc1f25c8a845fa1f392c02b27e9 Mon Sep 17 00:00:00 2001
+From 37c1b745004b455d8ad69c5e2da65fa77e39868f Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Sun, 21 Apr 2019 22:17:20 +0300
-Subject: [PATCH 16/91] ucm-imx8m-mini: spl: Refacoring ddr_init() call
+Subject: [PATCH 016/126] ucm-imx8m-mini: spl: Refacoring ddr_init() call

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
 ---
@@ -43,5 +43,5 @@ index 34f7683d2d..833183597a 100644
 
 #define I2C_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE)
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From a07c6130c9cba79e78f333e17529bee57cad61bb Mon Sep 17 00:00:00 2001
+From e0b70a34cfa94ec5399b71f680e4b4dd63b1b379 Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Sun, 21 Apr 2019 22:19:27 +0300
-Subject: [PATCH 17/91] ucm-imx8m-mini: Kconfig: Refacoring ddr init config
+Subject: [PATCH 017/126] ucm-imx8m-mini: Kconfig: Refacoring ddr init config
 option

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
@@ -32,5 +32,5 @@ index 1da11b2046..e6b334134f 100644
 	 imx8mm_val board configuration approach
 
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From b11be4155cda9dac8afd1fecfab3dc00370f4e3a Mon Sep 17 00:00:00 2001
+From 0001734a9f497a9287fbd1ca9f92d5b30e3cf9e4 Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Tue, 26 May 2020 21:33:48 +0300
-Subject: [PATCH 18/91] ucm-imx8m-mini: Makefile: Refacoring ddr init build
+Subject: [PATCH 018/126] ucm-imx8m-mini: Makefile: Refacoring ddr init build
 option

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
@@ -26,5 +26,5 @@ index b092c281ab..02d3393232 100644
 +obj-$(CONFIG_UCM_IMX8M_LPDDR4_VAL) += ddr/
 endif
 -- 
-2.17.1
+2.11.0

@@ -1,12 +1,12 @@
-From e811ab1437eb7dae3a27027612be3a70a1495481 Mon Sep 17 00:00:00 2001
+From 2ccda2a6956bfaa460fd871a5ba95ccb17ac5b6a Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Wed, 24 Apr 2019 13:55:44 +0300
-Subject: [PATCH 19/91] ucm-imx8m-mini: lpddr4_timing: Add ucm-imx8m-mini
+Subject: [PATCH 019/126] ucm-imx8m-mini: lpddr4_timing: Add ucm-imx8m-mini
 support

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
 ---
- board/compulab/ucm-imx8m-mini/lpddr4_timing.c | 39 +++++++++++--------
+ board/compulab/ucm-imx8m-mini/lpddr4_timing.c | 39 +++++++++++++++------------
 1 file changed, 22 insertions(+), 17 deletions(-)

 diff --git a/board/compulab/ucm-imx8m-mini/lpddr4_timing.c b/board/compulab/ucm-imx8m-mini/lpddr4_timing.c
@@ -102,5 +102,5 @@ index 9c80caea8b..dfd68ea9d8 100644
 	.ddrc_cfg_num = ARRAY_SIZE(lpddr4_ddrc_cfg),
 	.ddrphy_cfg = lpddr4_ddrphy_cfg,
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 61856dfbba647d1dc7ace4d0e20b6c2dd70356c5 Mon Sep 17 00:00:00 2001
+From 58e467d2a44188a047116e1945a45c4fdecc0c5a Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Wed, 1 May 2019 13:48:53 +0300
-Subject: [PATCH 20/91] ucm-imx8m-mini: config: Enable the new LPDDR4 config
+Subject: [PATCH 020/126] ucm-imx8m-mini: config: Enable the new LPDDR4 config

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
 ---
@@ -21,5 +21,5 @@ index 75531acb20..d45e7894e8 100644
 CONFIG_DEFAULT_DEVICE_TREE="ucm-imx8m-mini"
 CONFIG_FIT=y
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 4a41b9cfee034c1cf37639a02226bc4168a20bc6 Mon Sep 17 00:00:00 2001
+From e58e45b88859f214573df2d15eb727e4369ea6bc Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Tue, 30 Apr 2019 11:32:58 +0300
-Subject: [PATCH 21/91] ucm-imx8m-mini: Move FS support to defconfig
+Subject: [PATCH 021/126] ucm-imx8m-mini: Move FS support to defconfig

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
 ---
@@ -49,5 +49,5 @@ index 046dc243bc..8b55fd61e9 100644
 #define CONFIG_SYS_MMC_IMG_LOAD_PART	1
 
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From c5c284852f47909de25675a70a98f41057aec3bb Mon Sep 17 00:00:00 2001
+From 5309c7bfb05e76e83d0091ba0a192961bda6f992 Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Wed, 1 May 2019 21:48:56 +0300
-Subject: [PATCH 22/91] ucm-imx8m-mini: config: CONFIG_IMX_OPTEE=y
+Subject: [PATCH 022/126] ucm-imx8m-mini: config: CONFIG_IMX_OPTEE=y

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
 ---
@@ -21,5 +21,5 @@ index 3bce614aab..d457d263c4 100644
 CONFIG_FIT=y
 CONFIG_SPL_LOAD_FIT=y
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 9c604bbf23b9951a1e312f7ebaf8891d740047c6 Mon Sep 17 00:00:00 2001
+From a807f865492b22a83840252dde454899265dfbe2 Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Fri, 3 May 2019 23:00:08 +0300
-Subject: [PATCH 23/91] set extended temperature range
+Subject: [PATCH 023/126] set extended temperature range

 Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 ---
@@ -24,5 +24,5 @@ index 003cc857df..2e68d13e87 100644
 +	temperature = <115000>;
 +};
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From d4ff862d15542ac90847b63ac784dd2bc19c5e09 Mon Sep 17 00:00:00 2001
+From f6f8bfbfaa80842b1ecd7d1b3ce44b6404034468 Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Sat, 31 Aug 2019 20:18:05 +0300
-Subject: [PATCH 25/91] dts: Enable USB OTG support
+Subject: [PATCH 025/126] dts: Enable USB OTG support

 Enable USB OTG support, necessary for USB load and UMS.

@@ -25,5 +25,5 @@ index 6e59d1101c..c93cf1ac7a 100644
 
 &usbotg2 {
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 17c8e369aaf449e624c40eda88e184856c5e3875 Mon Sep 17 00:00:00 2001
+From 56cc0e465092c676b1f5d1401454bad06e316277 Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Sat, 31 Aug 2019 20:20:34 +0300
-Subject: [PATCH 26/91] env: Change boot sequence
+Subject: [PATCH 026/126] env: Change boot sequence

 Boot commands have been refactored to make them uniform and simplify a boot
 sequence edition.
@@ -12,7 +12,7 @@ if not, a pair of files Image + default DTB.

 Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 ---
- include/configs/ucm-imx8m-mini.h | 55 ++++++++++++++++----------------
+ include/configs/ucm-imx8m-mini.h | 55 ++++++++++++++++++++--------------------
 1 file changed, 28 insertions(+), 27 deletions(-)

 diff --git a/include/configs/ucm-imx8m-mini.h b/include/configs/ucm-imx8m-mini.h
@@ -99,5 +99,5 @@ index 7bbd0e73f9..e9e3b2cb1c 100644
 /* Link Definitions */
 #define CONFIG_LOADADDR			0x40480000
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From bdcd65e611083d56423826a4e4e0e99722cbffee Mon Sep 17 00:00:00 2001
+From b366281614785327ce65a2d0b000c2d187198b66 Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Tue, 10 Sep 2019 20:49:44 +0300
-Subject: [PATCH 27/91] Enable usb ethernet dongle asix-88179
+Subject: [PATCH 027/126] Enable usb ethernet dongle asix-88179

 Enable the dongle. In order to use it issue:
 usb start
@@ -26,5 +26,5 @@ index 8dbf544e86..3d750f7fe1 100644
 CONFIG_PINCTRL_IMX8M=y
 CONFIG_DM_REGULATOR=y
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 4b0fb07d9a1a69d4e47426aef870880128ba0ad4 Mon Sep 17 00:00:00 2001
+From 59f78def6097a2a24793ae3f92aae9bdc88af39b Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Wed, 1 Apr 2020 14:52:21 +0300
-Subject: [PATCH 28/91] ucm-ims8m-mini: dts: wp enable
+Subject: [PATCH 028/126] ucm-ims8m-mini: dts: wp enable

 Write protection enables for uSD card (the device usdhc2).

@@ -31,5 +31,5 @@ index c93cf1ac7a..3d8be3a09a 100644
 	vmmc-supply = <&reg_usdhc2_vmmc>;
 	status = "okay";
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 57d7bed9f9a28495b776238d200040708b8b6f21 Mon Sep 17 00:00:00 2001
+From 84e74f109aab8f75430d60e67acbc10a3f95988b Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Sun, 5 Apr 2020 17:19:21 +0300
-Subject: [PATCH 29/91] SPL: Enable bus I2C2
+Subject: [PATCH 029/126] SPL: Enable bus I2C2

 Enable the bus i2c1 (I2C2 in a schematic drawing) on SPL stage.

@@ -66,5 +66,5 @@ index e9e3b2cb1c..2400afe7ab 100644
 #define CONFIG_CMD_READ
 #define CONFIG_SERIAL_TAG
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From f64251dfd83b627c24e1de2d74ecfcf2a4db206c Mon Sep 17 00:00:00 2001
+From 584687f751c256836235d5b4321dbf2f427af6b3 Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Sun, 5 Apr 2020 17:36:34 +0300
-Subject: [PATCH 30/91] SPL: Adjust voltage for correct DDR initialisation
+Subject: [PATCH 030/126] SPL: Adjust voltage for correct DDR initialisation

 The voltage values, that PMIC BD71847 produces, differ from required and need to
 be adjusted before a memory training procedure.
@@ -15,10 +15,10 @@ Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 1 file changed, 8 insertions(+), 2 deletions(-)

 diff --git a/board/compulab/ucm-imx8m-mini/spl.c b/board/compulab/ucm-imx8m-mini/spl.c
-index aed967cce0..febd27c93e 100644
+index 61ac039ff3..2231cc1f6f 100644
 --- a/board/compulab/ucm-imx8m-mini/spl.c
 +++ b/board/compulab/ucm-imx8m-mini/spl.c
-@@ -174,8 +174,14 @@ int power_init_board(void)
+@@ -175,8 +175,14 @@ int power_init_board(void)
 	/* unlock the PMIC regs */
 	pmic_reg_write(p, BD71837_REGLOCK, 0x1);
 
@@ -36,5 +36,5 @@ index aed967cce0..febd27c93e 100644
 	/* lock the PMIC regs */
 	pmic_reg_write(p, BD71837_REGLOCK, 0x11);
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From a31a3902562fcc8b38183bd6ccd25cd9d333e0fb Mon Sep 17 00:00:00 2001
+From bf2f4b36ada27bf72a642f2e55ac39d5cfd9edaa Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Fri, 17 Apr 2020 20:38:46 +0300
-Subject: [PATCH 31/91] Enable env import/export commands
+Subject: [PATCH 031/126] Enable env import/export commands

 Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 ---
@@ -22,5 +22,5 @@ index 2400afe7ab..dfd7d9980f 100644
 
 #undef CONFIG_CMD_CRC32
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From d5e945141af4b6656d741caa0c3a7840b3c7204f Mon Sep 17 00:00:00 2001
+From 486ddc5f04efb9755d8b8ea07b9067ff35b21ed3 Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Sat, 18 Apr 2020 19:17:47 +0300
-Subject: [PATCH 32/91] env: Add env_mmcdev variable handling
+Subject: [PATCH 032/126] env: Add env_mmcdev variable handling

 Handle the variable env_mmcdev the following way:
 If the variable is set to an unsigned value, an actual environment is to be
@@ -34,5 +34,5 @@ index 97331e55d9..fca256439b 100644
 
 int mmc_map_to_kernel_blk(int devno)
 -- 
-2.17.1
+2.11.0

@@ -1,40 +1,31 @@
-From 1787abeea8fbcb9e284f5b2d4a4ba06bef8c2251 Mon Sep 17 00:00:00 2001
+From e2f68b309bbba5efba12713b4732bbdcc23d809c Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Mon, 19 Jul 2021 00:22:59 +0300
-Subject: [PATCH 33/91] Trivial cleaning
+Subject: [PATCH 033/126] Trivial cleaning

 Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 ---
- arch/arm/dts/Makefile                          | 4 ++--
+ arch/arm/dts/Makefile                          | 2 ++
 board/compulab/common/Makefile                 | 4 +++-
 board/compulab/common/common.c                 | 3 ++-
 board/compulab/common/common.h                 | 3 ++-
 board/compulab/common/eeprom.h                 | 3 ++-
 board/compulab/ucm-imx8m-mini/ucm-imx8m-mini.c | 2 +-
- 6 files changed, 12 insertions(+), 7 deletions(-)
+ 6 files changed, 12 insertions(+), 5 deletions(-)

 diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
-index 2b81a2bc62..6238d142af 100644
+index c31d483784..9781d3451c 100644
 --- a/arch/arm/dts/Makefile
 +++ b/arch/arm/dts/Makefile
-@@ -880,6 +880,8 @@ dtb-$(CONFIG_ARCH_IMX8M) += \
- dtb-$(CONFIG_ARCH_IMXRT) += imxrt1050-evk.dtb \
+@@ -888,6 +888,8 @@ dtb-$(CONFIG_ARCH_IMXRT) += imxrt1050-evk.dtb \
 	imxrt1020-evk.dtb
+ dtb-$(CONFIG_ARCH_IMX8ULP) += imx8ulp-evk.dtb imx8ulp-evk-i3c.dtb
 
 +dtb-$(CONFIG_TARGET_UCM_IMX8M_MINI) += ucm-imx8m-mini.dtb
 +
 dtb-$(CONFIG_RCAR_GEN2) += \
 	r8a7790-lager-u-boot.dtb \
 	r8a7790-stout-u-boot.dtb \
-@@ -890,8 +892,6 @@ dtb-$(CONFIG_RCAR_GEN2) += \
- 	r8a7794-alt-u-boot.dtb \
- 	r8a7794-silk-u-boot.dtb
- 
-dtb-$(CONFIG_TARGET_UCM_IMX8M_MINI) += ucm-imx8m-mini.dtb
-
- dtb-$(CONFIG_RCAR_GEN3) += \
- 	r8a774a1-beacon-rzg2m-kit.dtb \
- 	r8a774b1-beacon-rzg2n-kit.dtb \
 diff --git a/board/compulab/common/Makefile b/board/compulab/common/Makefile
 index 500858035f..0a26fdb426 100644
 --- a/board/compulab/common/Makefile
@@ -111,5 +102,5 @@ index fca256439b..cf3cefb30d 100644
     switch (value) {
     case 4096:
 -- 
-2.17.1
+2.11.0

@@ -1,45 +1,17 @@
-From 7d4680efc8133c631955c64518c6966505317644 Mon Sep 17 00:00:00 2001
+From 42104f3ba72deafdec230b2f0d82ba3741ab25fa Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
-Date: Mon, 19 Jul 2021 00:26:38 +0300
-Subject: [PATCH 34/91] Migration to rel_imx_5.4.3
+Date: Wed, 8 Dec 2021 14:56:15 +0200
+Subject: [PATCH 034/126] Migration to rel_imx_5.4.3

 Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 ---
- arch/arm/lib/bootm.c                           |  2 +-
- arch/arm/lib/cache-cp15.c                      |  2 +-
 arch/arm/mach-imx/misc.c                       |  2 --
 board/compulab/ucm-imx8m-mini/spl.c            | 13 +++++++------
- board/compulab/ucm-imx8m-mini/ucm-imx8m-mini.c | 11 ++++++-----
+ board/compulab/ucm-imx8m-mini/ucm-imx8m-mini.c | 10 ++++++----
 configs/ucm-imx8m-mini_defconfig               |  7 ++++++-
 include/configs/ucm-imx8m-mini.h               |  5 +++--
- 7 files changed, 24 insertions(+), 18 deletions(-)
+ 5 files changed, 22 insertions(+), 15 deletions(-)

-diff --git a/arch/arm/lib/bootm.c b/arch/arm/lib/bootm.c
-index e1bd628507..e4021e1025 100644
--- a/arch/arm/lib/bootm.c
-+++ b/arch/arm/lib/bootm.c
-@@ -154,7 +154,7 @@ static void setup_memory_tags(struct bd_info *bd)
- 	int i;
- 
- 	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
-		if(!bd->bi_dram[i].size)
-+		if (!gd->bd->bi_dram[i].size)
- 			continue;
- 		params->hdr.tag = ATAG_MEM;
- 		params->hdr.size = tag_size (tag_mem32);
-diff --git a/arch/arm/lib/cache-cp15.c b/arch/arm/lib/cache-cp15.c
-index 3212ea47f3..f6a9108fb9 100644
--- a/arch/arm/lib/cache-cp15.c
-+++ b/arch/arm/lib/cache-cp15.c
-@@ -117,7 +117,7 @@ __weak void dram_bank_mmu_setup(int bank)
- 	     i < (bd->bi_dram[bank].start >> MMU_SECTION_SHIFT) +
- 		 (bd->bi_dram[bank].size >> MMU_SECTION_SHIFT);
- 	     i++) {
-		 if(!bd->bi_dram[bank].size)
-+		if(!bd->bi_dram[bank].size)
- 			continue;
- 		set_section_dcache(i, DCACHE_DEFAULT_OPTION);
- 	}
 diff --git a/arch/arm/mach-imx/misc.c b/arch/arm/mach-imx/misc.c
 index 5f001926aa..9f53cc2168 100644
 --- a/arch/arm/mach-imx/misc.c
@@ -54,19 +26,19 @@ index 5f001926aa..9f53cc2168 100644
 			gd->bd->bi_dram[bank].size;
 		if (sp >= bank_end)
 diff --git a/board/compulab/ucm-imx8m-mini/spl.c b/board/compulab/ucm-imx8m-mini/spl.c
-index febd27c93e..316e8100fc 100644
+index 2231cc1f6f..fa1943477e 100644
 --- a/board/compulab/ucm-imx8m-mini/spl.c
 +++ b/board/compulab/ucm-imx8m-mini/spl.c
-@@ -19,7 +19,7 @@
- #include <asm/mach-imx/mxc_i2c.h>
+@@ -20,7 +20,7 @@
 #include <fsl_esdhc.h>
 #include <mmc.h>
+ 
 -#include <asm/arch/imx8m_ddr.h>
 +#include <asm/arch/ddr.h>
 #include "ddr/ddr.h"
 #include "ucm-imx8m-mini.h"
 
-@@ -99,6 +99,7 @@ int board_mmc_init(bd_t *bis)
+@@ -100,6 +100,7 @@ int board_mmc_init(bd_t *bis)
 	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
 		switch (i) {
 		case 0:
@@ -74,7 +46,7 @@ index febd27c93e..316e8100fc 100644
 			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
 			imx_iomux_v3_setup_multiple_pads(
 				usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
-@@ -108,6 +109,7 @@ int board_mmc_init(bd_t *bis)
+@@ -109,6 +110,7 @@ int board_mmc_init(bd_t *bis)
 			gpio_direction_output(USDHC2_PWR_GPIO, 1);
 			break;
 		case 1:
@@ -82,7 +54,7 @@ index febd27c93e..316e8100fc 100644
 			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
 			imx_iomux_v3_setup_multiple_pads(
 				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
-@@ -217,10 +219,12 @@ int board_fit_config_name_match(const char *name)
+@@ -218,10 +220,12 @@ int board_fit_config_name_match(const char *name)
 void board_init_f(ulong dummy)
 {
 	int ret;
@@ -97,7 +69,7 @@ index febd27c93e..316e8100fc 100644
 	arch_cpu_init();
 
 	board_early_init_f();
-@@ -229,9 +233,6 @@ void board_init_f(ulong dummy)
+@@ -230,9 +234,6 @@ void board_init_f(ulong dummy)
 
 	preloader_console_init();
 
@@ -108,7 +80,7 @@ index febd27c93e..316e8100fc 100644
 	if (ret) {
 		debug("spl_init() failed: %d\n", ret);
 diff --git a/board/compulab/ucm-imx8m-mini/ucm-imx8m-mini.c b/board/compulab/ucm-imx8m-mini/ucm-imx8m-mini.c
-index cf3cefb30d..fa06db9ec6 100644
+index cf3cefb30d..f262acf414 100644
 --- a/board/compulab/ucm-imx8m-mini/ucm-imx8m-mini.c
 +++ b/board/compulab/ucm-imx8m-mini/ucm-imx8m-mini.c
@@ -139,6 +139,8 @@ int board_early_init_f(void)
@@ -120,11 +92,10 @@ index cf3cefb30d..fa06db9ec6 100644
 	return 0;
 }
 
-@@ -149,11 +151,10 @@ int board_postclk_init(void)
- 	return 0;
+@@ -150,10 +152,10 @@ int board_postclk_init(void)
 }
 #endif
-
+ 
 -static phys_size_t imx8_ddr_size(void)
 +int board_phys_sdram_size(phys_size_t *size)
 {
@@ -134,7 +105,7 @@ index cf3cefb30d..fa06db9ec6 100644
 
     switch (value) {
     case 4096:
-@@ -165,12 +166,12 @@ static phys_size_t imx8_ddr_size(void)
+@@ -165,12 +167,12 @@ static phys_size_t imx8_ddr_size(void)
     case 768:
     case 512:
     case 256:
@@ -150,7 +121,7 @@ index cf3cefb30d..fa06db9ec6 100644
 	/* Get the top of usable RAM */
 ulong board_get_usable_ram_top(ulong total_size)
 diff --git a/configs/ucm-imx8m-mini_defconfig b/configs/ucm-imx8m-mini_defconfig
-index 2955b2f907..c57d88fa59 100644
+index 2955b2f907..a90b813a3d 100644
 --- a/configs/ucm-imx8m-mini_defconfig
 +++ b/configs/ucm-imx8m-mini_defconfig
@@ -1,3 +1,4 @@
@@ -158,13 +129,14 @@ index 2955b2f907..c57d88fa59 100644
 CONFIG_ARM=y
 CONFIG_ARCH_IMX8M=y
 CONFIG_SYS_TEXT_BASE=0x40200000
-@@ -8,10 +9,12 @@ CONFIG_IMX_OPTEE=y
+@@ -7,11 +8,13 @@ CONFIG_SPL_MMC_SUPPORT=y
+ CONFIG_IMX_OPTEE=y
 CONFIG_DEFAULT_DEVICE_TREE="ucm-imx8m-mini"
 CONFIG_FIT=y
- CONFIG_SPL_LOAD_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg,SPL_TEXT_BASE=0x7E1000"
 +CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
 +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/imx8m/imximage.cfg,SPL_TEXT_BASE=0x7E1000"
+ CONFIG_SPL_LOAD_FIT=y
+-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg,SPL_TEXT_BASE=0x7E1000"
 CONFIG_DEFAULT_FDT_FILE="ucm-imx8m-mini.dtb"
 CONFIG_ARCH_MISC_INIT=y
 CONFIG_SPL=y
@@ -207,5 +179,5 @@ index dfd7d9980f..30caaca5a1 100644
 #define CONFIG_SYS_SDRAM_BASE   PHYS_SDRAM
 #define PHYS_SDRAM_SIZE			0x80000000 /* 2GB DDR */
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From fa158dafefdcb52d8e10e8d6711fe90b759df091 Mon Sep 17 00:00:00 2001
+From 3d914d55d3fa43b8ca1f1d16473cf33e5917061c Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Tue, 16 Jun 2020 15:45:22 +0300
-Subject: [PATCH 35/91] Fix storages numeration order
+Subject: [PATCH 035/126] Fix storages numeration order

 Make u-boot enumerate storages in the same order as previous versions (2018.03)

@@ -36,5 +36,5 @@ index 3d8be3a09a..b191e87755 100644
 		compatible = "regulator-fixed";
 		regulator-name = "VSD_3V3";
 -- 
-2.17.1
+2.11.0

@@ -1,21 +1,21 @@
-From a5bb9ce368427a85ca72db9c512b9d9705126e7a Mon Sep 17 00:00:00 2001
+From dc542fe009df582db1a167902f72164de920fbcf Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Mon, 19 Jul 2021 00:58:48 +0300
-Subject: [PATCH 36/91] Fix memory size initialisation
+Subject: [PATCH 036/126] Fix memory size initialisation

 Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 ---
- board/compulab/plat/imx8mm/ddr/ddr.c          | 15 +-----
- .../compulab/ucm-imx8m-mini/ucm-imx8m-mini.c  | 48 +++++++++++--------
- .../compulab/ucm-imx8m-mini/ucm-imx8m-mini.h  |  6 +++
- configs/ucm-imx8m-mini_defconfig              |  2 +-
- 4 files changed, 35 insertions(+), 36 deletions(-)
+ board/compulab/plat/imx8mm/ddr/ddr.c           | 15 +-------
+ board/compulab/ucm-imx8m-mini/ucm-imx8m-mini.c | 47 ++++++++++++++------------
+ board/compulab/ucm-imx8m-mini/ucm-imx8m-mini.h |  6 ++++
+ configs/ucm-imx8m-mini_defconfig               |  2 +-
+ 4 files changed, 34 insertions(+), 36 deletions(-)

 diff --git a/board/compulab/plat/imx8mm/ddr/ddr.c b/board/compulab/plat/imx8mm/ddr/ddr.c
-index 7392fcdfaa..137a0b9f32 100644
+index 3c6b6ff489..1340475bef 100644
 --- a/board/compulab/plat/imx8mm/ddr/ddr.c
 +++ b/board/compulab/plat/imx8mm/ddr/ddr.c
-@@ -13,6 +13,7 @@
+@@ -14,6 +14,7 @@
 #include <asm/arch/clock.h>
 #include <asm/mach-imx/gpio.h>
 #include "ddr.h"
@@ -23,7 +23,7 @@ index 7392fcdfaa..137a0b9f32 100644
 
 /* Forward declarations */
 u32 cl_eeprom_get_ddrinfo(void);
-@@ -59,20 +60,6 @@ struct lpddr4_desc {
+@@ -60,20 +61,6 @@ struct lpddr4_desc {
 	char *desc[4];
 };
 
@@ -45,11 +45,11 @@ index 7392fcdfaa..137a0b9f32 100644
 static const struct lpddr4_desc lpddr4_array[] = {
 	{ .name = "Micron", .id = 0xff020008, .size = 2048, .count = 1, .timing = &ucm_dram_timing_ff020008}, //Only the first timing entry is in use
 diff --git a/board/compulab/ucm-imx8m-mini/ucm-imx8m-mini.c b/board/compulab/ucm-imx8m-mini/ucm-imx8m-mini.c
-index fa06db9ec6..0ffbbf3615 100644
+index f262acf414..8694201633 100644
 --- a/board/compulab/ucm-imx8m-mini/ucm-imx8m-mini.c
 +++ b/board/compulab/ucm-imx8m-mini/ucm-imx8m-mini.c
-@@ -153,25 +153,21 @@ int board_postclk_init(void)
- #endif
+@@ -154,25 +154,21 @@ int board_postclk_init(void)
+ 
 int board_phys_sdram_size(phys_size_t *size)
 {
 -    unsigned long value = readl(TCM_DATA_CFG);
@@ -89,15 +89,7 @@ index fa06db9ec6..0ffbbf3615 100644
 }
 	/* Get the top of usable RAM */
 ulong board_get_usable_ram_top(ulong total_size)
-@@ -188,6 +184,7 @@ int dram_init(void)
- 	phys_size_t sdram_size;
- 	int ret;
- 	ret = board_phys_sdram_size(&sdram_size);
-+	printf("%s: size %llu\n", __func__, sdram_size);
- 	if (ret)
- 		return ret;
- 
-@@ -219,21 +216,30 @@ int dram_init_banksize(void)
+@@ -220,21 +216,30 @@ int dram_init_banksize(void)
 	}
 
 	gd->bd->bi_dram[bank].start = PHYS_SDRAM;
@@ -147,7 +139,7 @@ index be698941da..c3380cb5ef 100644
 
 #endif
 diff --git a/configs/ucm-imx8m-mini_defconfig b/configs/ucm-imx8m-mini_defconfig
-index c57d88fa59..f42597b5c7 100644
+index a90b813a3d..3eb63bf1e6 100644
 --- a/configs/ucm-imx8m-mini_defconfig
 +++ b/configs/ucm-imx8m-mini_defconfig
@@ -5,7 +5,7 @@ CONFIG_SYS_TEXT_BASE=0x40200000
@@ -158,7 +150,7 @@ index c57d88fa59..f42597b5c7 100644
 +# CONFIG_IMX_OPTEE is not set
 CONFIG_DEFAULT_DEVICE_TREE="ucm-imx8m-mini"
 CONFIG_FIT=y
- CONFIG_SPL_LOAD_FIT=y
+ CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 912eada83c4e27cd5dca3fea9f1787b22c55ae25 Mon Sep 17 00:00:00 2001
+From 85923035d03ac133385f8d296d9722ed3375157d Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Sun, 21 Jun 2020 22:08:06 +0300
-Subject: [PATCH 37/91] env: Add to kernel command line rw rootwait
+Subject: [PATCH 037/126] env: Add to kernel command line rw rootwait

 Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 ---
@@ -28,5 +28,5 @@ index 30caaca5a1..e3e91c7f72 100644
 	"ulimage=load ${iface} ${dev}:${part} ${loadaddr} ${image}\0" \
 	"ulfdt=if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 6801a7a1c65cb87d00c72f1ee7f4074bd651eadf Mon Sep 17 00:00:00 2001
+From a93fbb4d91247528a8033cdaa6f99e8d3ca3efd7 Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Mon, 29 Jun 2020 18:15:26 +0300
-Subject: [PATCH 38/91] Move environment from 4M to 17k address
+Subject: [PATCH 038/126] Move environment from 4M to 17k address

 Change starting address of environment data on eMMC form (64 * 64k) to (34 * 512)
 in order to avoid possible conflicts with the first partition.
@@ -25,5 +25,5 @@ index e3e91c7f72..ad4e7997b1 100644
 #define CONFIG_SYS_MMC_ENV_DEV		0   /* USDHC2 */
 #define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC2 */
 -- 
-2.17.1
+2.11.0

@@ -1,11 +1,11 @@
-From eeec1e62d5133600bb5006f6dcc4feba2475cfce Mon Sep 17 00:00:00 2001
+From 745b74f41e51ff2c7590c6df9a3f2a94f884c2b4 Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Wed, 8 Jul 2020 08:03:28 +0300
-Subject: [PATCH 39/91] compulab: eeprom: Add DM support
+Subject: [PATCH 039/126] compulab: eeprom: Add DM support

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
 ---
- board/compulab/common/eeprom.c | 42 +++++++++++++++++++++++++++++-----
+ board/compulab/common/eeprom.c | 42 ++++++++++++++++++++++++++++++++++++------
 1 file changed, 36 insertions(+), 6 deletions(-)

 diff --git a/board/compulab/common/eeprom.c b/board/compulab/common/eeprom.c
@@ -77,5 +77,5 @@ index cc91f8a195..defd9b6446 100644
 	return res;
 }
 -- 
-2.17.1
+2.11.0

@@ -1,20 +1,20 @@
-From 8e4f334ab1c365dc0ba1d0ef8d0b31ac6caed9ad Mon Sep 17 00:00:00 2001
+From ab1153a5f4319338446cbdbea8398dd5ff387706 Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Mon, 19 Jul 2021 01:01:11 +0300
-Subject: [PATCH 40/91] mcm-imx8m-mini: Add basic support
+Subject: [PATCH 040/126] mcm-imx8m-mini: Add basic support

 Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 ---
- arch/arm/dts/Makefile                         |   1 +
- arch/arm/dts/mcm-imx8m-mini.dts               | 476 ++++++++++++++++++
- arch/arm/mach-imx/imx8m/Kconfig               |   7 +
- board/compulab/mcm-imx8m-mini/Kconfig         |  17 +
- board/compulab/mcm-imx8m-mini/Makefile        |  14 +
- .../compulab/mcm-imx8m-mini/mcm-imx8m-mini.c  | 352 +++++++++++++
- .../compulab/mcm-imx8m-mini/mcm-imx8m-mini.h  |  19 +
- board/compulab/mcm-imx8m-mini/spl.c           | 265 ++++++++++
- configs/mcm-imx8m-mini_defconfig              |  67 +++
- include/configs/mcm-imx8m-mini.h              | 308 ++++++++++++
+ arch/arm/dts/Makefile                          |   1 +
+ arch/arm/dts/mcm-imx8m-mini.dts                | 476 +++++++++++++++++++++++++
+ arch/arm/mach-imx/imx8m/Kconfig                |   7 +
+ board/compulab/mcm-imx8m-mini/Kconfig          |  17 +
+ board/compulab/mcm-imx8m-mini/Makefile         |  14 +
+ board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c | 352 ++++++++++++++++++
+ board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.h |  19 +
+ board/compulab/mcm-imx8m-mini/spl.c            | 265 ++++++++++++++
+ configs/mcm-imx8m-mini_defconfig               |  67 ++++
+ include/configs/mcm-imx8m-mini.h               | 308 ++++++++++++++++
 10 files changed, 1526 insertions(+)
 create mode 100644 arch/arm/dts/mcm-imx8m-mini.dts
 create mode 100644 board/compulab/mcm-imx8m-mini/Kconfig
@@ -26,11 +26,11 @@ Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 create mode 100644 include/configs/mcm-imx8m-mini.h

 diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
-index 6238d142af..5dacac3b5a 100644
+index 9781d3451c..c6b54163d0 100644
 --- a/arch/arm/dts/Makefile
 +++ b/arch/arm/dts/Makefile
-@@ -881,6 +881,7 @@ dtb-$(CONFIG_ARCH_IMXRT) += imxrt1050-evk.dtb \
- 	imxrt1020-evk.dtb
+@@ -889,6 +889,7 @@ dtb-$(CONFIG_ARCH_IMXRT) += imxrt1050-evk.dtb \
+ dtb-$(CONFIG_ARCH_IMX8ULP) += imx8ulp-evk.dtb imx8ulp-evk-i3c.dtb
 
 dtb-$(CONFIG_TARGET_UCM_IMX8M_MINI) += ucm-imx8m-mini.dtb
 +dtb-$(CONFIG_TARGET_MCM_IMX8M_MINI) += mcm-imx8m-mini.dtb
@@ -520,10 +520,10 @@ index 0000000000..2c3723a42c
 +	temperature = <115000>;
 +};
 diff --git a/arch/arm/mach-imx/imx8m/Kconfig b/arch/arm/mach-imx/imx8m/Kconfig
-index d4c41ba1aa..13e93cf0f1 100644
+index 4930b9bee6..a38ec31d25 100644
 --- a/arch/arm/mach-imx/imx8m/Kconfig
 +++ b/arch/arm/mach-imx/imx8m/Kconfig
-@@ -208,6 +208,12 @@ config TARGET_UCM_IMX8M_MINI
+@@ -266,6 +266,12 @@ config TARGET_UCM_IMX8M_MINI
 	select SUPPORT_SPL
 	select IMX8M_LPDDR4
 
@@ -536,7 +536,7 @@ index d4c41ba1aa..13e93cf0f1 100644
 endchoice
 
 source "board/freescale/imx8mq_evk/Kconfig"
-@@ -225,5 +231,6 @@ source "board/beacon/imx8mn/Kconfig"
+@@ -284,5 +290,6 @@ source "board/beacon/imx8mn/Kconfig"
 source "board/phytec/phycore_imx8mm/Kconfig"
 source "board/phytec/phycore_imx8mp/Kconfig"
 source "board/compulab/ucm-imx8m-mini/Kconfig"
@@ -1628,5 +1628,5 @@ index 0000000000..f5ab2f101b
 +#endif
 +#endif
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 84e001d6c6fe84c54f2029641860300f7941fb5a Mon Sep 17 00:00:00 2001
+From 7696c21869712bd70a49f6d43142437d3f5199e5 Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Wed, 8 Jul 2020 08:07:55 +0300
-Subject: [PATCH 41/91] mcm-imx8m-mini: env: config: Set the machine values
+Subject: [PATCH 041/126] mcm-imx8m-mini: env: config: Set the machine values

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
 ---
@@ -50,5 +50,5 @@ index 053895a2c0..3222fd715c 100644
 +/dev/mmcblk2boot0	0x1000	0x4000
 +#/dev/mmcblk1		0x1000	0x4000
 -- 
-2.17.1
+2.11.0

@@ -1,8 +1,8 @@
-From daa08d163bc71d8ac1e1347574729be7563f009f Mon Sep 17 00:00:00 2001
+From 754cce3320e6c237684530a6611cd8ad78cda536 Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Wed, 8 Jul 2020 08:10:42 +0300
-Subject: [PATCH 42/91] mcm-imx8m-mini: env: Add an option to print the machine
- env devices
+Subject: [PATCH 042/126] mcm-imx8m-mini: env: Add an option to print the
+ machine env devices

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
 ---
@@ -51,5 +51,5 @@ index 1d193bd437..ebd18b40ba 100644
 			/* ignore unknown options */
 			break;
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 7328ca230f8f8af35734a42a30554860e2f36240 Mon Sep 17 00:00:00 2001
+From e321143aaa0fd2913f731b5cf45d6ae08f11c31e Mon Sep 17 00:00:00 2001
 From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 Date: Mon, 19 Jul 2021 01:02:48 +0300
-Subject: [PATCH 43/91] mcm-imx8m-mini: Set EXTRAVERSION
+Subject: [PATCH 043/126] mcm-imx8m-mini: Set EXTRAVERSION

 Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
 ---
@@ -22,5 +22,5 @@ index 0451f445f6..22d2230a6f 100644
 
 # *DOCUMENTATION*
 -- 
-2.17.1
+2.11.0

@@ -1,11 +1,11 @@
-From 19bf71a555e5ab75f5157d39b2420cce43060133 Mon Sep 17 00:00:00 2001
+From 4e8e749b50ff87ce206d6446c02ff035b11e64f4 Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Wed, 8 Jul 2020 17:13:00 +0300
-Subject: [PATCH 44/91] mcm-imx8m-mini: config: Update defconfig
+Subject: [PATCH 044/126] mcm-imx8m-mini: config: Update defconfig

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
 ---
- configs/mcm-imx8m-mini_defconfig | 46 +++++++++++++++++++++++++++++---
+ configs/mcm-imx8m-mini_defconfig | 46 +++++++++++++++++++++++++++++++++++++---
 1 file changed, 43 insertions(+), 3 deletions(-)

 diff --git a/configs/mcm-imx8m-mini_defconfig b/configs/mcm-imx8m-mini_defconfig
@@ -119,5 +119,5 @@ index 80350afa7c..ce1cfb834a 100644
 +CONFIG_OF_LIBFDT_OVERLAY=y
 # CONFIG_EFI_LOADER is not set
 -- 
-2.17.1
+2.11.0

@@ -1,11 +1,11 @@
-From 020bfa6700660bd1c77c0282f88b288b5b058a3d Mon Sep 17 00:00:00 2001
+From cf8a47603118237f8b77790c71d4c78a926aac3c Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Wed, 8 Jul 2020 17:13:29 +0300
-Subject: [PATCH 45/91] mcm-imx8m-mini: config: Update .h config
+Subject: [PATCH 045/126] mcm-imx8m-mini: config: Update .h config

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
 ---
- include/configs/mcm-imx8m-mini.h | 48 ++++++--------------------------
+ include/configs/mcm-imx8m-mini.h | 48 ++++++++--------------------------------
 1 file changed, 9 insertions(+), 39 deletions(-)

 diff --git a/include/configs/mcm-imx8m-mini.h b/include/configs/mcm-imx8m-mini.h
@@ -145,5 +145,5 @@ index f5ab2f101b..dd0448efca 100644
 #define CONFIG_OF_BOARD_SETUP
 
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 161d9b8fcae9a58c5096574b7b815b9ad0f74d79 Mon Sep 17 00:00:00 2001
+From a2b63373c7d1f8e01405a0bb08a75ccd53607c71 Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Wed, 8 Jul 2020 17:28:54 +0300
-Subject: [PATCH 46/91] mcm-imx8m-mini: spl: Update the board spl
+Subject: [PATCH 046/126] mcm-imx8m-mini: spl: Update the board spl

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
 ---
@@ -54,5 +54,5 @@ index 7038a8e073..f59bac4cb9 100644
 +	return 0;
 +}
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 6ccb6f0a01d67e13ece4ddc6ec61f2ff69c0adff Mon Sep 17 00:00:00 2001
+From 3e43aa79f734982246d68cc6837601144d64ec72 Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Thu, 9 Jul 2020 12:35:27 +0300
-Subject: [PATCH 47/91] mcm-imx8m-mini: Fix dram_init_banksize() logics
+Subject: [PATCH 047/126] mcm-imx8m-mini: Fix dram_init_banksize() logics

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
 ---
@@ -32,5 +32,5 @@ index 1ec3ecbde7..9ece28b318 100644
 				bank_1_size - gd->bd->bi_dram[bank].start;
 		}
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From cbd85748102a4e9fb1251ff4313fd210de70a202 Mon Sep 17 00:00:00 2001
+From 9b7dbbb4c200496a6cca3ee42bfa85d8f6649f7c Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Thu, 9 Jul 2020 22:58:39 +0300
-Subject: [PATCH 48/91] mcm-imx8m-mini: Add board_usb_init() and
+Subject: [PATCH 048/126] mcm-imx8m-mini: Add board_usb_init() and
 board_usb_cleanup()

 Enable power on/off usb power in U-Boot.
@@ -40,5 +40,5 @@ index 9ece28b318..6cea3b38cd 100644
 {
 
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 80f1aafd56528a0405f8409d5c3337fbc1212e43 Mon Sep 17 00:00:00 2001
+From 4d8f74402acb4986f1db484b55d15c80de2f4acd Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Thu, 9 Jul 2020 23:00:55 +0300
-Subject: [PATCH 49/91] mcm-imx8m-mini: dts: Enable usbotg2 in host mode
+Subject: [PATCH 049/126] mcm-imx8m-mini: dts: Enable usbotg2 in host mode

 Make the ubsotg2 work in U-Boot in host mode.

@@ -25,5 +25,5 @@ index 2c3723a42c..85f4c46dd7 100644
 
 &cpu_alert0 {
 -- 
-2.17.1
+2.11.0

@@ -1,7 +1,7 @@
-From 6a6a9bb555195a8f40ee1426c7c6bdc3878b8cf2 Mon Sep 17 00:00:00 2001
+From ae8974e8a232e587112442a63be38b64b1675533 Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Thu, 9 Jul 2020 23:02:57 +0300
-Subject: [PATCH 50/91] mcm-imx8m-mini: config: Remove unused stuff
+Subject: [PATCH 050/126] mcm-imx8m-mini: config: Remove unused stuff

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
 ---
@@ -41,5 +41,5 @@ index ce1cfb834a..92cdad293d 100644
 CONFIG_SUPPORT_EMMC_BOOT=y
 CONFIG_MMC_IO_VOLTAGE=y
 -- 
-2.17.1
+2.11.0

@@ -1,12 +1,12 @@
-From 579a5ba04f8d70af5262e3d1abb6f2b615d289c8 Mon Sep 17 00:00:00 2001
+From bddd7484de0069acb92d6421dfcd1fc16bd346f4 Mon Sep 17 00:00:00 2001
 From: Valentin Raevsky <valentin@compulab.co.il>
 Date: Mon, 13 Jul 2020 10:55:06 +0300
-Subject: [PATCH 51/91] mcm-imx8m-mini: Remove dram_init_banksize() and
+Subject: [PATCH 051/126] mcm-imx8m-mini: Remove dram_init_banksize() and
 get_effective_memsize()

 Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
 ---
- .../compulab/mcm-imx8m-mini/mcm-imx8m-mini.c  | 76 -------------------
+ board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c | 76 --------------------------
 1 file changed, 76 deletions(-)

 diff --git a/board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c b/board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c
@@ -97,5 +97,5 @@ index 6cea3b38cd..7cfed94479 100644
 int ft_board_setup(void *blob, bd_t *bd)
 {
 -- 
-2.17.1
+2.11.0

@@ -0,0 +1,101 @@
+From 4fc2bc6314ba1ee0e2c3073bd3bc5c3e33887213 Mon Sep 17 00:00:00 2001
+From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+Date: Mon, 19 Jul 2021 01:06:57 +0300
+Subject: [PATCH 052/126] mcm-imx8m-mini: Move tcm to plat/imx8mm
+
+Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+---
+ board/compulab/mcm-imx8m-mini/Makefile         |  3 ++-
+ board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c |  2 +-
+ board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.h | 19 -------------------
+ board/compulab/mcm-imx8m-mini/spl.c            |  1 -
+ board/compulab/plat/imx8mm/ddr/ddr.h           |  9 +++++++++
+ 5 files changed, 12 insertions(+), 22 deletions(-)
+ delete mode 100644 board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.h
+
+diff --git a/board/compulab/mcm-imx8m-mini/Makefile b/board/compulab/mcm-imx8m-mini/Makefile
+index b926ed9cf9..8ade3b58c5 100644
+--- a/board/compulab/mcm-imx8m-mini/Makefile
+++ b/board/compulab/mcm-imx8m-mini/Makefile
+@@ -6,8 +6,9 @@
+ 
+ obj-y += mcm-imx8m-mini.o
+ 
+-ifdef CONFIG_SPL_BUILD
+ ccflags-y += -I$(srctree)/board/compulab/plat/imx8mm/
+
+ifdef CONFIG_SPL_BUILD
+ obj-y += spl.o
+ endif
+ 
+diff --git a/board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c b/board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c
+index 7cfed94479..20f322223c 100644
+--- a/board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c
+++ b/board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c
+@@ -27,7 +27,7 @@
+ #include <usb.h>
+ #include <asm/mach-imx/boot_mode.h>
+ #include <asm/mach-imx/video.h>
+-#include "mcm-imx8m-mini.h"
+#include "ddr/ddr.h"
+ 
+ DECLARE_GLOBAL_DATA_PTR;
+ 
+diff --git a/board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.h b/board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.h
+deleted file mode 100644
+index fc59756161..0000000000
+--- a/board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.h
+++ /dev/null
+@@ -1,19 +0,0 @@
+-/*
+- * Copyright 2017 NXP
+- *
+- * SPDX-License-Identifier:	GPL-2.0+
+- */
+-
+-#ifndef __MCM_IMX8M_MINI__
+-#define __MCM_IMX8M_MINI__
+-
+-#define TCM_DATA_CFG 0x7e0000
+-
+-struct lpddr4_tcm_desc {
+-	unsigned int size;
+-	unsigned int sign;
+-	unsigned int index;
+-	unsigned int count;
+-};
+-
+-#endif
+diff --git a/board/compulab/mcm-imx8m-mini/spl.c b/board/compulab/mcm-imx8m-mini/spl.c
+index f59bac4cb9..3f6cb65102 100644
+--- a/board/compulab/mcm-imx8m-mini/spl.c
+++ b/board/compulab/mcm-imx8m-mini/spl.c
+@@ -21,7 +21,6 @@
+ #include <fsl_esdhc_imx.h>
+ #include <mmc.h>
+ #include "ddr/ddr.h"
+-#include "mcm-imx8m-mini.h"
+ 
+ DECLARE_GLOBAL_DATA_PTR;
+ 
+diff --git a/board/compulab/plat/imx8mm/ddr/ddr.h b/board/compulab/plat/imx8mm/ddr/ddr.h
+index a66e8ec3c4..4d2a238439 100644
+--- a/board/compulab/plat/imx8mm/ddr/ddr.h
+++ b/board/compulab/plat/imx8mm/ddr/ddr.h
+@@ -14,4 +14,13 @@ extern struct dram_timing_info ucm_dram_timing_01050008;
+ 
+ void spl_dram_init(void);
+ 
+#define TCM_DATA_CFG 0x7e0000
+
+struct lpddr4_tcm_desc {
+	unsigned int size;
+	unsigned int sign;
+	unsigned int index;
+	unsigned int count;
+};
+
+ #endif
+-- 
+2.11.0
+
@@ -0,0 +1,702 @@
+From fbeb9ec1d92ce8968914308df8ab54d6288ce86e Mon Sep 17 00:00:00 2001
+From: Valentin Raevsky <valentin@compulab.co.il>
+Date: Wed, 15 Jul 2020 07:58:17 +0300
+Subject: [PATCH 053/126] mcm-imx8m-mini: Refactor spl code
+
+Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
+---
+ board/compulab/mcm-imx8m-mini/Makefile         |   4 +-
+ board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c |  27 ---
+ board/compulab/mcm-imx8m-mini/spl.c            | 265 +----------------------
+ board/compulab/plat/imx8mm/Makefile            |   1 +
+ board/compulab/plat/imx8mm/spl/Makefile        |   7 +
+ board/compulab/plat/imx8mm/spl/common.c        |  33 +++
+ board/compulab/plat/imx8mm/spl/spl.c           | 280 +++++++++++++++++++++++++
+ 7 files changed, 325 insertions(+), 292 deletions(-)
+ create mode 100644 board/compulab/plat/imx8mm/spl/Makefile
+ create mode 100644 board/compulab/plat/imx8mm/spl/common.c
+ create mode 100644 board/compulab/plat/imx8mm/spl/spl.c
+
+diff --git a/board/compulab/mcm-imx8m-mini/Makefile b/board/compulab/mcm-imx8m-mini/Makefile
+index 8ade3b58c5..9ce2875d6e 100644
+--- a/board/compulab/mcm-imx8m-mini/Makefile
+++ b/board/compulab/mcm-imx8m-mini/Makefile
+@@ -4,12 +4,12 @@
+ # SPDX-License-Identifier:      GPL-2.0+
+ #
+ 
+-obj-y += mcm-imx8m-mini.o
+-
+ ccflags-y += -I$(srctree)/board/compulab/plat/imx8mm/
+ 
+ ifdef CONFIG_SPL_BUILD
+ obj-y += spl.o
+else 
+obj-y += mcm-imx8m-mini.o
+ endif
+ 
+ obj-y += ../plat/imx8mm/
+diff --git a/board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c b/board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c
+index 20f322223c..d01b8f8767 100644
+--- a/board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c
+++ b/board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c
+@@ -31,33 +31,6 @@
+ 
+ DECLARE_GLOBAL_DATA_PTR;
+ 
+-#define UART_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_FSEL1)
+-#define WDOG_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_ODE | PAD_CTL_PUE | PAD_CTL_PE)
+-
+-static iomux_v3_cfg_t const uart_pads[] = {
+-	IMX8MM_PAD_UART3_RXD_UART3_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+-	IMX8MM_PAD_UART3_TXD_UART3_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+-};
+-
+-static iomux_v3_cfg_t const wdog_pads[] = {
+-	IMX8MM_PAD_GPIO1_IO02_WDOG1_WDOG_B  | MUX_PAD_CTRL(WDOG_PAD_CTRL),
+-};
+-
+-int board_early_init_f(void)
+-{
+-	struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
+-
+-	imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
+-
+-	set_wdog_reset(wdog);
+-
+-	imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
+-
+-	init_uart_clk(2);
+-
+-	return 0;
+-}
+-
+ #ifdef CONFIG_BOARD_POSTCLK_INIT
+ int board_postclk_init(void)
+ {
+diff --git a/board/compulab/mcm-imx8m-mini/spl.c b/board/compulab/mcm-imx8m-mini/spl.c
+index 3f6cb65102..d6ece8ef3e 100644
+--- a/board/compulab/mcm-imx8m-mini/spl.c
+++ b/board/compulab/mcm-imx8m-mini/spl.c
+@@ -1,270 +1,9 @@
+-/*
+- * Copyright 2020 CompuLab Ltd.
+- */
+-
+-#include <common.h>
+-#include <cpu_func.h>
+-#include <hang.h>
+-#include <spl.h>
+ #include <asm/io.h>
+ #include <asm/mach-imx/iomux-v3.h>
+-#include <asm/arch/clock.h>
+ #include <asm/arch/imx8mm_pins.h>
+#include <asm/arch/clock.h>
+ #include <asm/arch/sys_proto.h>
+-#include <asm/mach-imx/boot_mode.h>
+-#include <asm/arch/ddr.h>
+-
+-#include <power/pmic.h>
+-#include <power/bd71837.h>
+-#include <asm/mach-imx/gpio.h>
+-#include <asm/mach-imx/mxc_i2c.h>
+-#include <fsl_esdhc_imx.h>
+-#include <mmc.h>
+-#include "ddr/ddr.h"
+-
+-DECLARE_GLOBAL_DATA_PTR;
+-
+-int spl_board_boot_device(enum boot_device boot_dev_spl)
+-{
+-	switch (boot_dev_spl) {
+-	case SD2_BOOT:
+-	case MMC2_BOOT:
+-		return BOOT_DEVICE_MMC1;
+-	case SD3_BOOT:
+-	case MMC3_BOOT:
+-		return BOOT_DEVICE_MMC2;
+-	default:
+-		return BOOT_DEVICE_NONE;
+-	}
+-}
+-
+-#define I2C_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PE)
+-#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+-struct i2c_pads_info i2c_pad_info1 = {
+-	.scl = {
+-		.i2c_mode = IMX8MM_PAD_I2C2_SCL_I2C2_SCL | PC,
+-		.gpio_mode = IMX8MM_PAD_I2C2_SCL_GPIO5_IO16 | PC,
+-		.gp = IMX_GPIO_NR(5, 16),
+-	},
+-	.sda = {
+-		.i2c_mode = IMX8MM_PAD_I2C2_SDA_I2C2_SDA | PC,
+-		.gpio_mode = IMX8MM_PAD_I2C2_SDA_GPIO5_IO17 | PC,
+-		.gp = IMX_GPIO_NR(5, 17),
+-	},
+-};
+-
+-#define USDHC2_CD_GPIO	IMX_GPIO_NR(2, 18)
+-#define USDHC2_PWR_GPIO IMX_GPIO_NR(2, 19)
+-
+-#define USDHC_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE |PAD_CTL_PE | \
+-			 PAD_CTL_FSEL2)
+-#define USDHC_GPIO_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE1)
+-
+-static iomux_v3_cfg_t const usdhc3_pads[] = {
+-	IMX8MM_PAD_NAND_WE_B_USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+-	IMX8MM_PAD_NAND_WP_B_USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+-	IMX8MM_PAD_NAND_DATA04_USDHC3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+-	IMX8MM_PAD_NAND_DATA05_USDHC3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+-	IMX8MM_PAD_NAND_DATA06_USDHC3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+-	IMX8MM_PAD_NAND_DATA07_USDHC3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+-	IMX8MM_PAD_NAND_RE_B_USDHC3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+-	IMX8MM_PAD_NAND_CE2_B_USDHC3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+-	IMX8MM_PAD_NAND_CE3_B_USDHC3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+-	IMX8MM_PAD_NAND_CLE_USDHC3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+-};
+-
+-static iomux_v3_cfg_t const usdhc2_pads[] = {
+-	IMX8MM_PAD_SD2_CLK_USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+-	IMX8MM_PAD_SD2_CMD_USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+-	IMX8MM_PAD_SD2_DATA0_USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+-	IMX8MM_PAD_SD2_DATA1_USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+-	IMX8MM_PAD_SD2_DATA2_USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+-	IMX8MM_PAD_SD2_DATA3_USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+-	IMX8MM_PAD_SD2_RESET_B_GPIO2_IO19 | MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL),
+-};
+-
+-/*
+- * The evk board uses DAT3 to detect CD card plugin,
+- * in u-boot we mux the pin to GPIO when doing board_mmc_getcd.
+- */
+-static iomux_v3_cfg_t const usdhc2_cd_pad =
+-	IMX8MM_PAD_SD2_DATA3_GPIO2_IO18 | MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL);
+-
+-static iomux_v3_cfg_t const usdhc2_dat3_pad =
+-	IMX8MM_PAD_SD2_DATA3_USDHC2_DATA3 |
+-	MUX_PAD_CTRL(USDHC_PAD_CTRL);
+-
+-
+-static struct fsl_esdhc_cfg usdhc_cfg[2] = {
+-	{USDHC2_BASE_ADDR, 0, 4},
+-	{USDHC3_BASE_ADDR, 0, 8},
+-};
+-
+-int board_mmc_init(bd_t *bis)
+-{
+-	int i, ret;
+-	/*
+-	 * According to the board_mmc_init() the following map is done:
+-	 * (U-Boot device node)    (Physical Port)
+-	 * mmc0                    USDHC1
+-	 * mmc1                    USDHC2
+-	 */
+-	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+-		switch (i) {
+-		case 0:
+-			init_clk_usdhc(1);
+-			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+-			imx_iomux_v3_setup_multiple_pads(
+-				usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+-			gpio_request(USDHC2_PWR_GPIO, "usdhc2_reset");
+-			gpio_direction_output(USDHC2_PWR_GPIO, 0);
+-			udelay(500);
+-			gpio_direction_output(USDHC2_PWR_GPIO, 1);
+-			break;
+-		case 1:
+-			init_clk_usdhc(2);
+-			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+-			imx_iomux_v3_setup_multiple_pads(
+-				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+-			break;
+-		default:
+-			printf("Warning: you configured more USDHC controllers"
+-				"(%d) than supported by the board\n", i + 1);
+-			return -EINVAL;
+-		}
+-
+-		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+-		if (ret)
+-			return ret;
+-	}
+-
+-	return 0;
+-}
+-
+-int board_mmc_getcd(struct mmc *mmc)
+-{
+-	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+-	int ret = 0;
+-
+-	switch (cfg->esdhc_base) {
+-	case USDHC3_BASE_ADDR:
+-		ret = 1;
+-		break;
+-	case USDHC2_BASE_ADDR:
+-		imx_iomux_v3_setup_pad(usdhc2_cd_pad);
+-		gpio_request(USDHC2_CD_GPIO, "usdhc2 cd");
+-		gpio_direction_input(USDHC2_CD_GPIO);
+-
+-		/*
+-		 * Since it is the DAT3 pin, this pin is pulled to
+-		 * low voltage if no card
+-		 */
+-		ret = gpio_get_value(USDHC2_CD_GPIO);
+-
+-		imx_iomux_v3_setup_pad(usdhc2_dat3_pad);
+-		return ret;
+-	}
+-
+-	return 1;
+-}
+-
+-#ifdef CONFIG_POWER
+-#define I2C_PMIC	1
+-int power_init_board(void)
+-{
+-	struct pmic *p;
+-	int ret;
+-
+-	ret = power_bd71837_init(I2C_PMIC);
+-	if (ret)
+-		printf("power init failed");
+-
+-	p = pmic_get("BD71837");
+-	pmic_probe(p);
+-
+-
+-	/* decrease RESET key long push time from the default 10s to 10ms */
+-	pmic_reg_write(p, BD71837_PWRONCONFIG1, 0x0);
+-
+-	/* unlock the PMIC regs */
+-	pmic_reg_write(p, BD71837_REGLOCK, 0x1);
+-
+-	/* decrease VDD_ARM to 0.85V for 1.2GHz operation */
+-	pmic_reg_write(p, BD71837_BUCK1_VOLT_RUN, 0x0f);
+-
+-	/* increase VDD_DRAM to 0.975V (9v5 required but not supported)*/
+-	pmic_reg_write(p, BD71837_BUCK5_VOLT, 0x83);
+-
+-	/* increase NVCC_DRAM_1V2 to 1.2v for DDR4 */
+-	pmic_reg_write(p, BD71837_BUCK8_VOLT, 0x28);
+-
+-	/* lock the PMIC regs */
+-	pmic_reg_write(p, BD71837_REGLOCK, 0x11);
+-
+-	return 0;
+-}
+-#else
+-int power_init_board(void) { return 0; }
+-#endif
+-
+-void spl_board_init(void)
+-{
+-#ifndef CONFIG_SPL_USB_SDP_SUPPORT
+-	/* Serial download mode */
+-	if (is_usb_boot()) {
+-		puts("Back to ROM, SDP\n");
+-		restore_boot_params();
+-	}
+-#endif
+-	puts("Normal Boot\n");
+-}
+-
+-#ifdef CONFIG_SPL_LOAD_FIT
+-int board_fit_config_name_match(const char *name)
+-{
+-	/* Just empty function now - can't decide what to choose */
+-	debug("%s: %s\n", __func__, name);
+-
+-	return 0;
+-}
+-#endif
+-
+-void board_init_f(ulong dummy)
+-{
+-	int ret;
+-	/* Clear the BSS. */
+-	memset(__bss_start, 0, __bss_end - __bss_start);
+-
+-	arch_cpu_init();
+-
+-	board_early_init_f();
+-
+-	timer_init();
+-
+-	preloader_console_init();
+-
+-	ret = spl_init();
+-	if (ret) {
+-		debug("spl_init() failed: %d\n", ret);
+-		hang();
+-	}
+-
+-	enable_tzc380();
+-
+-	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+-
+-	power_init_board();
+-	/* DDR initialization */
+-	spl_dram_init();
+-
+-	board_init_r(NULL, 0);
+-}
+-
+-int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+-{
+-	puts ("resetting ...\n");
+-
+-	reset_cpu(WDOG1_BASE_ADDR);
+ 
+int spl_board_private_init(void) {
+ 	return 0;
+ }
+diff --git a/board/compulab/plat/imx8mm/Makefile b/board/compulab/plat/imx8mm/Makefile
+index 04b9b2e8f8..2f68e0523e 100644
+--- a/board/compulab/plat/imx8mm/Makefile
+++ b/board/compulab/plat/imx8mm/Makefile
+@@ -1,2 +1,3 @@
+ obj-y += ddr/
+ obj-y += eeprom/
+obj-y += spl/
+diff --git a/board/compulab/plat/imx8mm/spl/Makefile b/board/compulab/plat/imx8mm/spl/Makefile
+new file mode 100644
+index 0000000000..a3a9acaa6e
+--- /dev/null
+++ b/board/compulab/plat/imx8mm/spl/Makefile
+@@ -0,0 +1,7 @@
+ccflags-y += -I$(srctree)/board/compulab/plat/imx8mm/
+
+obj-y += common.o
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+endif
+diff --git a/board/compulab/plat/imx8mm/spl/common.c b/board/compulab/plat/imx8mm/spl/common.c
+new file mode 100644
+index 0000000000..5f1d1e5b97
+--- /dev/null
+++ b/board/compulab/plat/imx8mm/spl/common.c
+@@ -0,0 +1,33 @@
+#include <asm/io.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/arch/imx8mm_pins.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+
+#define UART_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_FSEL1)
+#define WDOG_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_ODE | PAD_CTL_PUE | PAD_CTL_PE)
+
+static iomux_v3_cfg_t const uart_pads[] = {
+	IMX8MM_PAD_UART3_RXD_UART3_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	IMX8MM_PAD_UART3_TXD_UART3_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const wdog_pads[] = {
+	IMX8MM_PAD_GPIO1_IO02_WDOG1_WDOG_B  | MUX_PAD_CTRL(WDOG_PAD_CTRL),
+};
+
+int board_early_init_f(void)
+{
+	struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
+
+	imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
+
+	set_wdog_reset(wdog);
+
+	imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
+
+	init_uart_clk(2);
+
+	return 0;
+}
+
+diff --git a/board/compulab/plat/imx8mm/spl/spl.c b/board/compulab/plat/imx8mm/spl/spl.c
+new file mode 100644
+index 0000000000..50aa6bea3f
+--- /dev/null
+++ b/board/compulab/plat/imx8mm/spl/spl.c
+@@ -0,0 +1,280 @@
+/*
+ * Copyright 2020 CompuLab Ltd.
+ */
+
+#include <common.h>
+#include <cpu_func.h>
+#include <hang.h>
+#include <init.h>
+#include <spl.h>
+#include <asm/io.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/imx8mm_pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-imx/boot_mode.h>
+#include <asm/arch/ddr.h>
+#include <linux/delay.h>
+
+#include <power/pmic.h>
+#include <power/bd71837.h>
+#include <asm/mach-imx/gpio.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <fsl_esdhc_imx.h>
+#include <mmc.h>
+#include "ddr/ddr.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int spl_board_boot_device(enum boot_device boot_dev_spl)
+{
+	switch (boot_dev_spl) {
+	case SD2_BOOT:
+	case MMC2_BOOT:
+		return BOOT_DEVICE_MMC1;
+	case SD3_BOOT:
+	case MMC3_BOOT:
+		return BOOT_DEVICE_MMC2;
+	default:
+		return BOOT_DEVICE_NONE;
+	}
+}
+
+#define I2C_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PE)
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode = IMX8MM_PAD_I2C2_SCL_I2C2_SCL | PC,
+		.gpio_mode = IMX8MM_PAD_I2C2_SCL_GPIO5_IO16 | PC,
+		.gp = IMX_GPIO_NR(5, 16),
+	},
+	.sda = {
+		.i2c_mode = IMX8MM_PAD_I2C2_SDA_I2C2_SDA | PC,
+		.gpio_mode = IMX8MM_PAD_I2C2_SDA_GPIO5_IO17 | PC,
+		.gp = IMX_GPIO_NR(5, 17),
+	},
+};
+
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(2, 18)
+#define USDHC2_PWR_GPIO IMX_GPIO_NR(2, 19)
+
+#define USDHC_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE |PAD_CTL_PE | \
+			 PAD_CTL_FSEL2)
+#define USDHC_GPIO_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE1)
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+	IMX8MM_PAD_NAND_WE_B_USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MM_PAD_NAND_WP_B_USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MM_PAD_NAND_DATA04_USDHC3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MM_PAD_NAND_DATA05_USDHC3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MM_PAD_NAND_DATA06_USDHC3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MM_PAD_NAND_DATA07_USDHC3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MM_PAD_NAND_RE_B_USDHC3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MM_PAD_NAND_CE2_B_USDHC3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MM_PAD_NAND_CE3_B_USDHC3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MM_PAD_NAND_CLE_USDHC3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	IMX8MM_PAD_SD2_CLK_USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MM_PAD_SD2_CMD_USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MM_PAD_SD2_DATA0_USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MM_PAD_SD2_DATA1_USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MM_PAD_SD2_DATA2_USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MM_PAD_SD2_DATA3_USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MM_PAD_SD2_RESET_B_GPIO2_IO19 | MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL),
+};
+
+/*
+ * The evk board uses DAT3 to detect CD card plugin,
+ * in u-boot we mux the pin to GPIO when doing board_mmc_getcd.
+ */
+static iomux_v3_cfg_t const usdhc2_cd_pad =
+	IMX8MM_PAD_SD2_DATA3_GPIO2_IO18 | MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL);
+
+static iomux_v3_cfg_t const usdhc2_dat3_pad =
+	IMX8MM_PAD_SD2_DATA3_USDHC2_DATA3 |
+	MUX_PAD_CTRL(USDHC_PAD_CTRL);
+
+
+static struct fsl_esdhc_cfg usdhc_cfg[2] = {
+	{USDHC2_BASE_ADDR, 0, 4},
+	{USDHC3_BASE_ADDR, 0, 8},
+};
+
+int board_mmc_init(bd_t *bis)
+{
+	int i, ret;
+	/*
+	 * According to the board_mmc_init() the following map is done:
+	 * (U-Boot device node)    (Physical Port)
+	 * mmc0                    USDHC1
+	 * mmc1                    USDHC2
+	 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			init_clk_usdhc(1);
+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+			gpio_request(USDHC2_PWR_GPIO, "usdhc2_reset");
+			gpio_direction_output(USDHC2_PWR_GPIO, 0);
+			udelay(500);
+			gpio_direction_output(USDHC2_PWR_GPIO, 1);
+			break;
+		case 1:
+			init_clk_usdhc(2);
+			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers"
+				"(%d) than supported by the board\n", i + 1);
+			return -EINVAL;
+		}
+
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC3_BASE_ADDR:
+		ret = 1;
+		break;
+	case USDHC2_BASE_ADDR:
+		imx_iomux_v3_setup_pad(usdhc2_cd_pad);
+		gpio_request(USDHC2_CD_GPIO, "usdhc2 cd");
+		gpio_direction_input(USDHC2_CD_GPIO);
+
+		/*
+		 * Since it is the DAT3 pin, this pin is pulled to
+		 * low voltage if no card
+		 */
+		ret = gpio_get_value(USDHC2_CD_GPIO);
+
+		imx_iomux_v3_setup_pad(usdhc2_dat3_pad);
+		return ret;
+	}
+
+	return 1;
+}
+
+#ifdef CONFIG_POWER
+#define I2C_PMIC	1
+int power_init_board(void)
+{
+	struct pmic *p;
+	int ret;
+
+	ret = power_bd71837_init(I2C_PMIC);
+	if (ret)
+		printf("power init failed");
+
+	p = pmic_get("BD71837");
+	pmic_probe(p);
+
+
+	/* decrease RESET key long push time from the default 10s to 10ms */
+	pmic_reg_write(p, BD71837_PWRONCONFIG1, 0x0);
+
+	/* unlock the PMIC regs */
+	pmic_reg_write(p, BD71837_REGLOCK, 0x1);
+
+	/* decrease VDD_ARM to 0.85V for 1.2GHz operation */
+	pmic_reg_write(p, BD71837_BUCK1_VOLT_RUN, 0x0f);
+
+	/* increase VDD_DRAM to 0.975V (9v5 required but not supported)*/
+	pmic_reg_write(p, BD71837_BUCK5_VOLT, 0x83);
+
+	/* increase NVCC_DRAM_1V2 to 1.2v for DDR4 */
+	pmic_reg_write(p, BD71837_BUCK8_VOLT, 0x28);
+
+	/* lock the PMIC regs */
+	pmic_reg_write(p, BD71837_REGLOCK, 0x11);
+
+	return 0;
+}
+#else
+int power_init_board(void) { return 0; }
+#endif
+
+__weak int spl_board_private_init(void) {
+	return 0;
+}
+
+void spl_board_init(void)
+{
+#ifndef CONFIG_SPL_USB_SDP_SUPPORT
+	/* Serial download mode */
+	if (is_usb_boot()) {
+		puts("Back to ROM, SDP\n");
+		restore_boot_params();
+	}
+#endif
+	if (spl_board_private_init()) {
+		debug("spl_board_private_init() failed\n");
+		hang();
+	}
+	puts("Normal Boot\n");
+}
+
+#ifdef CONFIG_SPL_LOAD_FIT
+int board_fit_config_name_match(const char *name)
+{
+	/* Just empty function now - can't decide what to choose */
+	debug("%s: %s\n", __func__, name);
+
+	return 0;
+}
+#endif
+
+void board_init_f(ulong dummy)
+{
+	int ret;
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	arch_cpu_init();
+
+	board_early_init_f();
+
+	timer_init();
+
+	preloader_console_init();
+
+	ret = spl_init();
+	if (ret) {
+		debug("spl_init() failed: %d\n", ret);
+		hang();
+	}
+
+	enable_tzc380();
+
+	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+
+	power_init_board();
+	/* DDR initialization */
+	spl_dram_init();
+
+	board_init_r(NULL, 0);
+}
+
+int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+	puts ("resetting ...\n");
+
+	reset_cpu(WDOG1_BASE_ADDR);
+
+	return 0;
+}
+-- 
+2.11.0
+
@@ -0,0 +1,53 @@
+From 6bce15eb561907ce960577ca4dc2eb2a00394107 Mon Sep 17 00:00:00 2001
+From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+Date: Mon, 19 Jul 2021 15:06:14 +0300
+Subject: [PATCH 055/126] cpl-imx8m-mini: Set LOCALVERSION intead of
+ EXTRAVERSION
+
+Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+---
+ Makefile                         | 2 +-
+ configs/mcm-imx8m-mini_defconfig | 1 +
+ configs/ucm-imx8m-mini_defconfig | 1 +
+ 3 files changed, 3 insertions(+), 1 deletion(-)
+
+diff --git a/Makefile b/Makefile
+index 22d2230a6f..0451f445f6 100644
+--- a/Makefile
+++ b/Makefile
+@@ -3,7 +3,7 @@
+ VERSION = 2021
+ PATCHLEVEL = 04
+ SUBLEVEL =
+-EXTRAVERSION = -mcm-imx8m-mini-1.0
+EXTRAVERSION =
+ NAME =
+ 
+ # *DOCUMENTATION*
+diff --git a/configs/mcm-imx8m-mini_defconfig b/configs/mcm-imx8m-mini_defconfig
+index 92cdad293d..a4c3c90f83 100644
+--- a/configs/mcm-imx8m-mini_defconfig
+++ b/configs/mcm-imx8m-mini_defconfig
+@@ -13,6 +13,7 @@ CONFIG_SPL_SERIAL_SUPPORT=y
+ CONFIG_SPL=y
+ CONFIG_CSF_SIZE=0x2000
+ CONFIG_SPL_TEXT_BASE=0x7E1000
+CONFIG_LOCALVERSION="-mcm-imx8m-mini-1.0"
+ CONFIG_FIT=y
+ CONFIG_FIT_EXTERNAL_OFFSET=0x3000
+ CONFIG_SPL_LOAD_FIT=y
+diff --git a/configs/ucm-imx8m-mini_defconfig b/configs/ucm-imx8m-mini_defconfig
+index 77b68b8e49..2c98eaa256 100644
+--- a/configs/ucm-imx8m-mini_defconfig
+++ b/configs/ucm-imx8m-mini_defconfig
+@@ -14,6 +14,7 @@ CONFIG_SPL_SERIAL_SUPPORT=y
+ CONFIG_SPL=y
+ CONFIG_CSF_SIZE=0x2000
+ CONFIG_SPL_TEXT_BASE=0x7E1000
+CONFIG_LOCALVERSION="-ucm-imx8m-mini-2.0"
+ CONFIG_FIT=y
+ CONFIG_FIT_EXTERNAL_OFFSET=0x3000
+ CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
+-- 
+2.11.0
+
@@ -0,0 +1,852 @@
+From 8ce4046b2b4a29a5158e904f11c128b9c42ea5a9 Mon Sep 17 00:00:00 2001
+From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+Date: Mon, 19 Jul 2021 15:46:11 +0300
+Subject: [PATCH 056/126] cpl-imx8m-mini: Refactor .h configs
+
+Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+---
+ include/configs/cpl-imx8m-mini.h | 275 +++++++++++++++++++++++++++++++++++++++
+ include/configs/mcm-imx8m-mini.h | 265 +------------------------------------
+ include/configs/ucm-imx8m-mini.h | 268 +-------------------------------------
+ 3 files changed, 277 insertions(+), 531 deletions(-)
+ create mode 100644 include/configs/cpl-imx8m-mini.h
+
+diff --git a/include/configs/cpl-imx8m-mini.h b/include/configs/cpl-imx8m-mini.h
+new file mode 100644
+index 0000000000..dd8120f4dc
+--- /dev/null
+++ b/include/configs/cpl-imx8m-mini.h
+@@ -0,0 +1,275 @@
+/*
+ * Copyright 2020 CompuLab
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CPL_IMX8M_MINI_H
+#define __CPL_IMX8M_MINI_H
+
+#include <linux/sizes.h>
+#include <asm/arch/imx-regs.h>
+#include "imx_env.h"
+
+#define CONFIG_SPL_MAX_SIZE		(148 * 1024)
+#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
+#define CONFIG_SYS_UBOOT_BASE		(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
+
+#ifdef CONFIG_SPL_BUILD
+/*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
+#define CONFIG_SPL_WATCHDOG_SUPPORT
+#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+
+#define CONFIG_SPL_STACK            0x920000
+#define CONFIG_SPL_BSS_START_ADDR   0x910000
+#define CONFIG_SPL_BSS_MAX_SIZE     SZ_8K
+#define CONFIG_SYS_SPL_MALLOC_START 0x42200000
+#define CONFIG_SYS_SPL_MALLOC_SIZE  SZ_512K
+
+/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
+#define CONFIG_MALLOC_F_ADDR        0x912000
+
+#define CONFIG_SPL_ABORT_ON_RAW_IMAGE /* For RAW image gives a error info not panic */
+
+#undef CONFIG_DM_MMC
+#undef CONFIG_DM_PMIC
+#undef CONFIG_DM_PMIC_PFUZE100
+
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
+
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_BD71837
+
+#endif /*ifdef CONFIG_SPL_BUILD*/
+
+#define CONFIG_CMD_READ
+#define CONFIG_SERIAL_TAG
+#define CONFIG_FASTBOOT_USB_DEV 0
+
+#define CONFIG_REMAKE_ELF
+
+#define CONFIG_BOARD_POSTCLK_INIT
+
+/* Flat Device Tree Definitions */
+#define CONFIG_OF_BOARD_SETUP
+
+#undef CONFIG_CMD_IMLS
+
+#undef CONFIG_CMD_CRC32
+#undef CONFIG_BOOTM_NETBSD
+
+/* ENET Config */
+/* ENET1 */
+#if defined(CONFIG_CMD_NET)
+#define CONFIG_ETHPRIME                 "FEC"
+
+#define CONFIG_FEC_XCV_TYPE             RGMII
+#define CONFIG_FEC_MXC_PHYADDR          0
+#define FEC_QUIRK_ENET_MAC
+
+#define CONFIG_PHY_GIGE
+#define IMX_FEC_BASE			0x30BE0000
+
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ATHEROS
+#endif
+
+#define CONFIG_MFG_ENV_SETTINGS \
+	"mfgtool_args=setenv bootargs console=${console},${baudrate} " \
+		"rdinit=/linuxrc " \
+		"g_mass_storage.stall=0 g_mass_storage.removable=1 " \
+		"g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
+		"g_mass_storage.iSerialNumber=\"\" "\
+		"clk_ignore_unused "\
+		"\0" \
+	"initrd_addr=0x43800000\0" \
+	"initrd_high=0xffffffff\0" \
+	"emmc_dev=1\0" \
+	"sd_dev=0\0" \
+	"bootcmd_mfg=run mfgtool_args;  if iminfo ${initrd_addr}; then "\
+					   "booti ${loadaddr} ${initrd_addr} ${fdt_addr};"\
+					"else echo \"Run fastboot ...\"; fastboot 0; fi\0" \
+/* Initial environment variables */
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	CONFIG_MFG_ENV_SETTINGS \
+	"autoload=off\0" \
+	"script=boot.scr\0" \
+	"image=Image\0" \
+	"console=ttymxc2,115200 earlycon=ec_imx6q,0x30880000,115200\0" \
+	"fdt_addr=0x43000000\0"			\
+	"fdt_high=0xffffffffffffffff\0"		\
+	"boot_fdt=yes\0" \
+	"fdt_file="CONFIG_DEFAULT_DTB"\0" \
+	"initrd_addr=0x43800000\0"		\
+	"initrd_high=0xffffffffffffffff\0" \
+	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+	"mmcautodetect=yes\0" \
+	"root_opt=rootwait rw\0" \
+	"emmc_ul=setenv iface mmc; setenv dev 2; setenv part 1;" \
+	"setenv bootargs console=${console} root=/dev/mmcblk2p2 ${root_opt};\0" \
+	"sd_ul=setenv iface mmc; setenv dev 1; setenv part 1;" \
+	"setenv bootargs console=${console} root=/dev/mmcblk1p2 ${root_opt};\0" \
+	"usb_ul=usb start; setenv iface usb; setenv dev 0; setenv part 1;" \
+	"setenv bootargs console=${console} root=/dev/sda2 ${root_opt};\0" \
+	"ulbootscript=load ${iface} ${dev}:${part} ${loadaddr} ${script};\0" \
+	"ulimage=load ${iface} ${dev}:${part} ${loadaddr} ${image}\0" \
+	"ulfdt=if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+		"load ${iface} ${dev}:${part} ${fdt_addr} ${fdt_file}; fi;\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source\0" \
+	"netargs=setenv bootargs console=${console} " \
+		"root=/dev/nfs " \
+		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+	"netboot=echo Booting from net ...; " \
+		"run netargs;  " \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"${get_cmd} ${loadaddr} ${image}; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+				"booti ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"echo WARN: Cannot load the DT; " \
+			"fi; " \
+		"else " \
+			"booti; " \
+		"fi;\0"
+#define CONFIG_BOOTCOMMAND \
+	"for src in sd_ul usb_ul emmc_ul; do " \
+		"run ${src}; " \
+		"if run ulbootscript; then " \
+			"run bootscript; " \
+		"else " \
+			"if run ulimage; then " \
+				"if run ulfdt; then " \
+					"booti ${loadaddr} - ${fdt_addr}; " \
+				"else " \
+					"if test ${boot_fdt} != yes; then " \
+						"booti ${loadaddr}; " \
+					"fi; " \
+				"fi; " \
+			"fi; " \
+		"fi; " \
+	"done; " \
+	"usb start; ums 0 mmc ${mmcdev};"
+
+/* Link Definitions */
+#define CONFIG_LOADADDR			0x40480000
+
+#define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
+
+#define CONFIG_SYS_INIT_RAM_ADDR        0x40000000
+#define CONFIG_SYS_INIT_RAM_SIZE        0x80000
+#define CONFIG_SYS_INIT_SP_OFFSET \
+        (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+        (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_SYS_MMC_ENV_DEV		1   /* USDHC2 */
+#define CONFIG_SYS_MMC_ENV_PART		1
+#define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC2 */
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		((CONFIG_ENV_SIZE + (2*1024) + (16*1024)) * 1024)
+
+#define PHYS_SDRAM              0x40000000
+#define PHYS_SDRAM_2            0x100000000
+#define PHYS_SDRAM_SIZE   0 /* Memory chip autodetection */
+#define PHYS_SDRAM_2_SIZE 0 /* Memory chip autodetection */
+#define CONFIG_NR_DRAM_BANKS    4
+#define CONFIG_SYS_SDRAM_BASE   PHYS_SDRAM
+
+#define MEMTEST_DIVIDER   2
+#define MEMTEST_NUMERATOR 1
+
+#define CONFIG_BAUDRATE			115200
+
+#define CONFIG_MXC_UART_BASE		UART3_BASE_ADDR
+
+/* Monitor Command Prompt */
+#undef CONFIG_SYS_PROMPT
+#define CONFIG_SYS_PROMPT		"u-boot=> "
+#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
+#define CONFIG_SYS_CBSIZE              2048
+#define CONFIG_SYS_MAXARGS             64
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+					sizeof(CONFIG_SYS_PROMPT) + 16)
+
+#define CONFIG_SYS_MMC_IMG_LOAD_PART	1
+
+#define CONFIG_IMX_BOOTAUX
+
+/* USDHC */
+#define CONFIG_FSL_USDHC
+
+#define CONFIG_SYS_FSL_USDHC_NUM	2
+#define CONFIG_SYS_FSL_ESDHC_ADDR       0
+
+#ifndef CONFIG_DM_I2C
+#define CONFIG_SYS_I2C
+#endif
+#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
+#define CONFIG_SYS_I2C_SPEED		100000
+
+/* EEPROM */
+#define CONFIG_ENV_EEPROM_IS_ON_I2C
+#define CONFIG_SYS_I2C_EEPROM_BUS		1
+#define CONFIG_SYS_I2C_SLAVE			0x00
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
+#define CONFIG_SYS_EEPROM_SIZE			256
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
+
+/* USB configs */
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USBD_HS
+
+#define CONFIG_CMD_USB_MASS_STORAGE
+#define CONFIG_USB_GADGET_MASS_STORAGE
+#define CONFIG_USB_FUNCTION_MASS_STORAGE
+
+#endif
+
+#define CONFIG_USB_GADGET_VBUS_DRAW 2
+
+#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_USB_MAX_CONTROLLER_COUNT         2
+
+#ifdef CONFIG_VIDEO
+#define CONFIG_VIDEO_MXS
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASH_SCREEN_ALIGN
+#define CONFIG_CMD_BMP
+#define CONFIG_BMP_16BPP
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_IMX_VIDEO_SKIP
+#define CONFIG_RM67191
+#endif
+
+#define CONFIG_BOARD_POSTCLK_INIT
+#define CONFIG_OF_BOARD_SETUP
+
+#endif
+diff --git a/include/configs/mcm-imx8m-mini.h b/include/configs/mcm-imx8m-mini.h
+index dd0448efca..602091a782 100644
+--- a/include/configs/mcm-imx8m-mini.h
+++ b/include/configs/mcm-imx8m-mini.h
+@@ -7,270 +7,7 @@
+ #ifndef __MCM_IMX8M_MINI_H
+ #define __MCM_IMX8M_MINI_H
+ 
+-#include <linux/sizes.h>
+-#include <asm/arch/imx-regs.h>
+-#include "imx_env.h"
+-
+-#define CONFIG_SPL_MAX_SIZE		(148 * 1024)
+-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
+-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300
+-#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
+-#define CONFIG_SYS_UBOOT_BASE		(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
+-
+-#ifdef CONFIG_SPL_BUILD
+-/*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
+-#define CONFIG_SPL_WATCHDOG_SUPPORT
+-#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+-#define CONFIG_SPL_I2C_SUPPORT
+-#define CONFIG_SPL_LIBCOMMON_SUPPORT
+-#define CONFIG_SPL_LIBGENERIC_SUPPORT
+-
+-#define CONFIG_SPL_STACK            0x920000
+-#define CONFIG_SPL_BSS_START_ADDR   0x910000
+-#define CONFIG_SPL_BSS_MAX_SIZE     SZ_8K
+-#define CONFIG_SYS_SPL_MALLOC_START 0x42200000
+-#define CONFIG_SYS_SPL_MALLOC_SIZE  SZ_512K
+-
+-/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
+-#define CONFIG_MALLOC_F_ADDR        0x912000
+-
+-#define CONFIG_SPL_ABORT_ON_RAW_IMAGE /* For RAW image gives a error info not panic */
+-
+-#undef CONFIG_DM_MMC
+-#undef CONFIG_DM_PMIC
+-#undef CONFIG_DM_PMIC_PFUZE100
+-
+-#define CONFIG_SYS_I2C
+-#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+-#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
+-#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
+-
+-#define CONFIG_POWER
+-#define CONFIG_POWER_I2C
+-#define CONFIG_POWER_BD71837
+-
+-#endif /*ifdef CONFIG_SPL_BUILD*/
+-
+-#define CONFIG_CMD_READ
+-#define CONFIG_SERIAL_TAG
+-#define CONFIG_FASTBOOT_USB_DEV 0
+-
+-#define CONFIG_REMAKE_ELF
+-
+-#define CONFIG_BOARD_POSTCLK_INIT
+-
+-/* Flat Device Tree Definitions */
+-#define CONFIG_OF_BOARD_SETUP
+-
+-#undef CONFIG_CMD_IMLS
+-
+-#undef CONFIG_CMD_CRC32
+-#undef CONFIG_BOOTM_NETBSD
+-
+-/* ENET Config */
+-/* ENET1 */
+-#if defined(CONFIG_CMD_NET)
+-#define CONFIG_ETHPRIME                 "FEC"
+-
+-#define CONFIG_FEC_XCV_TYPE             RGMII
+-#define CONFIG_FEC_MXC_PHYADDR          0
+-#define FEC_QUIRK_ENET_MAC
+-
+-#define CONFIG_PHY_GIGE
+-#define IMX_FEC_BASE			0x30BE0000
+-
+-#define CONFIG_PHYLIB
+-#define CONFIG_PHY_ATHEROS
+-#endif
+-
+-#define CONFIG_MFG_ENV_SETTINGS \
+-	"mfgtool_args=setenv bootargs console=${console},${baudrate} " \
+-		"rdinit=/linuxrc " \
+-		"g_mass_storage.stall=0 g_mass_storage.removable=1 " \
+-		"g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
+-		"g_mass_storage.iSerialNumber=\"\" "\
+-		"clk_ignore_unused "\
+-		"\0" \
+-	"initrd_addr=0x43800000\0" \
+-	"initrd_high=0xffffffff\0" \
+-	"emmc_dev=1\0" \
+-	"sd_dev=0\0" \
+-	"bootcmd_mfg=run mfgtool_args;  if iminfo ${initrd_addr}; then "\
+-					   "booti ${loadaddr} ${initrd_addr} ${fdt_addr};"\
+-					"else echo \"Run fastboot ...\"; fastboot 0; fi\0" \
+-/* Initial environment variables */
+-#define CONFIG_EXTRA_ENV_SETTINGS		\
+-	CONFIG_MFG_ENV_SETTINGS \
+-	"autoload=off\0" \
+-	"script=boot.scr\0" \
+-	"image=Image\0" \
+-	"console=ttymxc2,115200 earlycon=ec_imx6q,0x30880000,115200\0" \
+-	"fdt_addr=0x43000000\0"			\
+-	"fdt_high=0xffffffffffffffff\0"		\
+-	"boot_fdt=yes\0" \
+-	"fdt_file="CONFIG_DEFAULT_DTB"\0" \
+-	"initrd_addr=0x43800000\0"		\
+-	"initrd_high=0xffffffffffffffff\0" \
+-	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+-	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+-	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+-	"mmcautodetect=yes\0" \
+-	"root_opt=rootwait rw\0" \
+-	"emmc_ul=setenv iface mmc; setenv dev 2; setenv part 1;" \
+-	"setenv bootargs console=${console} root=/dev/mmcblk2p2 ${root_opt};\0" \
+-	"sd_ul=setenv iface mmc; setenv dev 1; setenv part 1;" \
+-	"setenv bootargs console=${console} root=/dev/mmcblk1p2 ${root_opt};\0" \
+-	"usb_ul=usb start; setenv iface usb; setenv dev 0; setenv part 1;" \
+-	"setenv bootargs console=${console} root=/dev/sda2 ${root_opt};\0" \
+-	"ulbootscript=load ${iface} ${dev}:${part} ${loadaddr} ${script};\0" \
+-	"ulimage=load ${iface} ${dev}:${part} ${loadaddr} ${image}\0" \
+-	"ulfdt=if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+-		"load ${iface} ${dev}:${part} ${fdt_addr} ${fdt_file}; fi;\0" \
+-	"bootscript=echo Running bootscript from mmc ...; " \
+-		"source\0" \
+-	"netargs=setenv bootargs console=${console} " \
+-		"root=/dev/nfs " \
+-		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+-	"netboot=echo Booting from net ...; " \
+-		"run netargs;  " \
+-		"if test ${ip_dyn} = yes; then " \
+-			"setenv get_cmd dhcp; " \
+-		"else " \
+-			"setenv get_cmd tftp; " \
+-		"fi; " \
+-		"${get_cmd} ${loadaddr} ${image}; " \
+-		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+-			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+-				"booti ${loadaddr} - ${fdt_addr}; " \
+-			"else " \
+-				"echo WARN: Cannot load the DT; " \
+-			"fi; " \
+-		"else " \
+-			"booti; " \
+-		"fi;\0"
+-#define CONFIG_BOOTCOMMAND \
+-	"for src in sd_ul usb_ul emmc_ul; do " \
+-		"run ${src}; " \
+-		"if run ulbootscript; then " \
+-			"run bootscript; " \
+-		"else " \
+-			"if run ulimage; then " \
+-				"if run ulfdt; then " \
+-					"booti ${loadaddr} - ${fdt_addr}; " \
+-				"else " \
+-					"if test ${boot_fdt} != yes; then " \
+-						"booti ${loadaddr}; " \
+-					"fi; " \
+-				"fi; " \
+-			"fi; " \
+-		"fi; " \
+-	"done; " \
+-	"usb start; ums 0 mmc ${mmcdev};"
+-
+-/* Link Definitions */
+-#define CONFIG_LOADADDR			0x40480000
+-
+-#define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
+-
+-#define CONFIG_SYS_INIT_RAM_ADDR        0x40000000
+-#define CONFIG_SYS_INIT_RAM_SIZE        0x80000
+-#define CONFIG_SYS_INIT_SP_OFFSET \
+-        (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+-#define CONFIG_SYS_INIT_SP_ADDR \
+-        (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+-
+-#define CONFIG_ENV_OVERWRITE
+-#define CONFIG_SYS_MMC_ENV_DEV		1   /* USDHC2 */
+-#define CONFIG_SYS_MMC_ENV_PART		1
+-#define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC2 */
+-
+-/* Size of malloc() pool */
+-#define CONFIG_SYS_MALLOC_LEN		((CONFIG_ENV_SIZE + (2*1024) + (16*1024)) * 1024)
+-
+-#define PHYS_SDRAM              0x40000000
+-#define PHYS_SDRAM_2            0x100000000
+-#define PHYS_SDRAM_SIZE   0 /* Memory chip autodetection */
+-#define PHYS_SDRAM_2_SIZE 0 /* Memory chip autodetection */
+-#define CONFIG_NR_DRAM_BANKS    4
+-#define CONFIG_SYS_SDRAM_BASE   PHYS_SDRAM
+-
+-#define MEMTEST_DIVIDER   2
+-#define MEMTEST_NUMERATOR 1
+-
+-#define CONFIG_BAUDRATE			115200
+-
+-#define CONFIG_MXC_UART_BASE		UART3_BASE_ADDR
+-
+-/* Monitor Command Prompt */
+-#undef CONFIG_SYS_PROMPT
+-#define CONFIG_SYS_PROMPT		"u-boot=> "
+-#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
+-#define CONFIG_SYS_CBSIZE              2048
+-#define CONFIG_SYS_MAXARGS             64
+-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+-#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+-					sizeof(CONFIG_SYS_PROMPT) + 16)
+-
+-#define CONFIG_SYS_MMC_IMG_LOAD_PART	1
+-
+-#define CONFIG_IMX_BOOTAUX
+-
+-/* USDHC */
+-#define CONFIG_FSL_USDHC
+-
+-#define CONFIG_SYS_FSL_USDHC_NUM	2
+-#define CONFIG_SYS_FSL_ESDHC_ADDR       0
+-
+-#ifndef CONFIG_DM_I2C
+-#define CONFIG_SYS_I2C
+-#endif
+-#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+-#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
+-#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
+-#define CONFIG_SYS_I2C_SPEED		100000
+-
+-/* EEPROM */
+-#define CONFIG_ENV_EEPROM_IS_ON_I2C
+-#define CONFIG_SYS_I2C_EEPROM_BUS		1
+-#define CONFIG_SYS_I2C_SLAVE			0x00
+-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
+-#define CONFIG_SYS_EEPROM_SIZE			256
+-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
+-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
+-
+-/* USB configs */
+-#ifndef CONFIG_SPL_BUILD
+-#define CONFIG_CMD_USB
+-#define CONFIG_USB_STORAGE
+-#define CONFIG_USBD_HS
+-
+-#define CONFIG_CMD_USB_MASS_STORAGE
+-#define CONFIG_USB_GADGET_MASS_STORAGE
+-#define CONFIG_USB_FUNCTION_MASS_STORAGE
+-
+-#endif
+-
+-#define CONFIG_USB_GADGET_VBUS_DRAW 2
+-
+-#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
+-#define CONFIG_USB_MAX_CONTROLLER_COUNT         2
+-
+-#ifdef CONFIG_VIDEO
+-#define CONFIG_VIDEO_MXS
+-#define CONFIG_VIDEO_LOGO
+-#define CONFIG_SPLASH_SCREEN
+-#define CONFIG_SPLASH_SCREEN_ALIGN
+-#define CONFIG_CMD_BMP
+-#define CONFIG_BMP_16BPP
+-#define CONFIG_VIDEO_BMP_RLE8
+-#define CONFIG_VIDEO_BMP_LOGO
+-#define CONFIG_IMX_VIDEO_SKIP
+-#define CONFIG_RM67191
+-#endif
+-
+-#define CONFIG_BOARD_POSTCLK_INIT
+-#define CONFIG_OF_BOARD_SETUP
+#include "cpl-imx8m-mini.h"
+ 
+ #if defined(CONFIG_ANDROID_SUPPORT)
+ #include "mcm-imx8m-mini_android.h"
+diff --git a/include/configs/ucm-imx8m-mini.h b/include/configs/ucm-imx8m-mini.h
+index 75c6102f10..b3d6082a66 100644
+--- a/include/configs/ucm-imx8m-mini.h
+++ b/include/configs/ucm-imx8m-mini.h
+@@ -7,273 +7,7 @@
+ #ifndef __UCM_IMX8M_MINI_H
+ #define __UCM_IMX8M_MINI_H
+ 
+-#include <linux/sizes.h>
+-#include <asm/arch/imx-regs.h>
+-#include "imx_env.h"
+-
+-#define CONFIG_SPL_MAX_SIZE		(148 * 1024)
+-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
+-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300
+-#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
+-#define CONFIG_SYS_UBOOT_BASE		(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
+-
+-#ifdef CONFIG_SPL_BUILD
+-/*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
+-#define CONFIG_SPL_WATCHDOG_SUPPORT
+-#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+-#define CONFIG_SPL_I2C_SUPPORT
+-#define CONFIG_SPL_LIBCOMMON_SUPPORT
+-#define CONFIG_SPL_LIBGENERIC_SUPPORT
+-
+-#define CONFIG_SPL_STACK            0x920000
+-#define CONFIG_SPL_BSS_START_ADDR   0x910000
+-#define CONFIG_SPL_BSS_MAX_SIZE     SZ_8K
+-#define CONFIG_SYS_SPL_MALLOC_START 0x42200000
+-#define CONFIG_SYS_SPL_MALLOC_SIZE  SZ_512K
+-
+-/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
+-#define CONFIG_MALLOC_F_ADDR        0x912000
+-
+-#define CONFIG_SPL_ABORT_ON_RAW_IMAGE /* For RAW image gives a error info not panic */
+-
+-#undef CONFIG_DM_MMC
+-#undef CONFIG_DM_PMIC
+-#undef CONFIG_DM_PMIC_PFUZE100
+-
+-#define CONFIG_SYS_I2C
+-#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+-#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
+-#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
+-
+-#define CONFIG_POWER
+-#define CONFIG_POWER_I2C
+-#define CONFIG_POWER_BD71837
+-
+-#endif /*ifdef CONFIG_SPL_BUILD*/
+-
+-#define CONFIG_CMD_READ
+-#define CONFIG_SERIAL_TAG
+-#define CONFIG_FASTBOOT_USB_DEV 0
+-
+-#define CONFIG_REMAKE_ELF
+-
+-#define CONFIG_BOARD_POSTCLK_INIT
+-
+-/* Flat Device Tree Definitions */
+-#define CONFIG_OF_BOARD_SETUP
+-
+-#undef CONFIG_CMD_IMLS
+-
+-#undef CONFIG_CMD_CRC32
+-#undef CONFIG_BOOTM_NETBSD
+-
+-/* ENET Config */
+-/* ENET1 */
+-#if defined(CONFIG_CMD_NET)
+-#define CONFIG_ETHPRIME                 "FEC"
+-
+-#define CONFIG_FEC_XCV_TYPE             RGMII
+-#define CONFIG_FEC_MXC_PHYADDR          0
+-#define FEC_QUIRK_ENET_MAC
+-
+-#define CONFIG_PHY_GIGE
+-#define IMX_FEC_BASE			0x30BE0000
+-
+-#define CONFIG_PHYLIB
+-#define CONFIG_PHY_ATHEROS
+-#endif
+-
+-#define CONFIG_MFG_ENV_SETTINGS \
+-	"mfgtool_args=setenv bootargs console=${console},${baudrate} " \
+-		"rdinit=/linuxrc " \
+-		"g_mass_storage.stall=0 g_mass_storage.removable=1 " \
+-		"g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
+-		"g_mass_storage.iSerialNumber=\"\" "\
+-		"clk_ignore_unused "\
+-		"\0" \
+-	"initrd_addr=0x43800000\0" \
+-	"initrd_high=0xffffffff\0" \
+-	"emmc_dev=1\0" \
+-	"sd_dev=0\0" \
+-	"bootcmd_mfg=run mfgtool_args;  if iminfo ${initrd_addr}; then "\
+-					   "booti ${loadaddr} ${initrd_addr} ${fdt_addr};"\
+-					"else echo \"Run fastboot ...\"; fastboot 0; fi\0" \
+-/* Initial environment variables */
+-#define CONFIG_EXTRA_ENV_SETTINGS		\
+-	CONFIG_MFG_ENV_SETTINGS \
+-	"autoload=off\0" \
+-	"script=boot.scr\0" \
+-	"image=Image\0" \
+-	"console=ttymxc2,115200 earlycon=ec_imx6q,0x30880000,115200\0" \
+-	"fdt_addr=0x43000000\0"			\
+-	"fdt_high=0xffffffffffffffff\0"		\
+-	"boot_fdt=yes\0" \
+-	"fdt_file="CONFIG_DEFAULT_DTB"\0" \
+-	"initrd_addr=0x43800000\0"		\
+-	"initrd_high=0xffffffffffffffff\0" \
+-	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+-	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+-	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+-	"mmcautodetect=yes\0" \
+-	"root_opt=rootwait rw\0" \
+-	"emmc_ul=setenv iface mmc; setenv dev 2; setenv part 1;" \
+-	"setenv bootargs console=${console} root=/dev/mmcblk2p2 ${root_opt};\0" \
+-	"sd_ul=setenv iface mmc; setenv dev 1; setenv part 1;" \
+-	"setenv bootargs console=${console} root=/dev/mmcblk1p2 ${root_opt};\0" \
+-	"usb_ul=usb start; setenv iface usb; setenv dev 0; setenv part 1;" \
+-	"setenv bootargs console=${console} root=/dev/sda2 ${root_opt};\0" \
+-	"ulbootscript=load ${iface} ${dev}:${part} ${loadaddr} ${script};\0" \
+-	"ulimage=load ${iface} ${dev}:${part} ${loadaddr} ${image}\0" \
+-	"ulfdt=if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+-		"load ${iface} ${dev}:${part} ${fdt_addr} ${fdt_file}; fi;\0" \
+-	"bootscript=echo Running bootscript from mmc ...; " \
+-		"source\0" \
+-	"netargs=setenv bootargs console=${console} " \
+-		"root=/dev/nfs " \
+-		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+-	"netboot=echo Booting from net ...; " \
+-		"run netargs;  " \
+-		"if test ${ip_dyn} = yes; then " \
+-			"setenv get_cmd dhcp; " \
+-		"else " \
+-			"setenv get_cmd tftp; " \
+-		"fi; " \
+-		"${get_cmd} ${loadaddr} ${image}; " \
+-		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+-			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+-				"booti ${loadaddr} - ${fdt_addr}; " \
+-			"else " \
+-				"echo WARN: Cannot load the DT; " \
+-			"fi; " \
+-		"else " \
+-			"booti; " \
+-		"fi;\0"
+-#define CONFIG_BOOTCOMMAND \
+-	"for src in sd_ul usb_ul emmc_ul; do " \
+-		"run ${src}; " \
+-		"if run ulbootscript; then " \
+-			"run bootscript; " \
+-		"else " \
+-			"if run ulimage; then " \
+-				"if run ulfdt; then " \
+-					"booti ${loadaddr} - ${fdt_addr}; " \
+-				"else " \
+-					"if test ${boot_fdt} != yes; then " \
+-						"booti ${loadaddr}; " \
+-					"fi; " \
+-				"fi; " \
+-			"fi; " \
+-		"fi; " \
+-	"done; " \
+-	"usb start; ums 0 mmc ${mmcdev};"
+-
+-/* Link Definitions */
+-#define CONFIG_LOADADDR			0x40480000
+-
+-#define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
+-
+-#define CONFIG_SYS_INIT_RAM_ADDR        0x40000000
+-#define CONFIG_SYS_INIT_RAM_SIZE        0x80000
+-#define CONFIG_SYS_INIT_SP_OFFSET \
+-        (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+-#define CONFIG_SYS_INIT_SP_ADDR \
+-        (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+-
+-#define CONFIG_ENV_OVERWRITE
+-#define CONFIG_SYS_MMC_ENV_DEV		1   /* USDHC2 */
+-#define CONFIG_SYS_MMC_ENV_PART		1
+-#define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC2 */
+-
+-/* Size of malloc() pool */
+-#define CONFIG_SYS_MALLOC_LEN		((CONFIG_ENV_SIZE + (2*1024) + (16*1024)) * 1024)
+-
+-#define PHYS_SDRAM              0x40000000
+-#define PHYS_SDRAM_2            0x100000000
+-#define PHYS_SDRAM_SIZE         0x80000000 /* 2GB default size*/
+-#undef PHYS_SDRAM_2_SIZE /* Memory chip autodetection */
+-#define CONFIG_NR_DRAM_BANKS    4
+-
+-#define CONFIG_SYS_SDRAM_BASE   PHYS_SDRAM
+-#define PHYS_SDRAM_SIZE			0x80000000 /* 2GB DDR */
+-#define PHYS_SDRAM_2_SIZE		0x40000000
+-
+-#define MEMTEST_DIVIDER   2
+-#define MEMTEST_NUMERATOR 1
+-
+-#define CONFIG_BAUDRATE			115200
+-
+-#define CONFIG_MXC_UART_BASE		UART3_BASE_ADDR
+-
+-/* Monitor Command Prompt */
+-#undef CONFIG_SYS_PROMPT
+-#define CONFIG_SYS_PROMPT		"u-boot=> "
+-#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
+-#define CONFIG_SYS_CBSIZE              2048
+-#define CONFIG_SYS_MAXARGS             64
+-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+-#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+-					sizeof(CONFIG_SYS_PROMPT) + 16)
+-
+-#define CONFIG_SYS_MMC_IMG_LOAD_PART	1
+-
+-#define CONFIG_IMX_BOOTAUX
+-
+-/* USDHC */
+-#define CONFIG_FSL_USDHC
+-
+-#define CONFIG_SYS_FSL_USDHC_NUM	2
+-#define CONFIG_SYS_FSL_ESDHC_ADDR       0
+-
+-#ifndef CONFIG_DM_I2C
+-#define CONFIG_SYS_I2C
+-#endif
+-#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+-#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
+-#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
+-#define CONFIG_SYS_I2C_SPEED		100000
+-
+-/* EEPROM */
+-#define CONFIG_ENV_EEPROM_IS_ON_I2C
+-#define CONFIG_SYS_I2C_EEPROM_BUS		1
+-#define CONFIG_SYS_I2C_SLAVE			0x00
+-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
+-#define CONFIG_SYS_EEPROM_SIZE			256
+-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
+-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
+-
+-/* USB configs */
+-#ifndef CONFIG_SPL_BUILD
+-#define CONFIG_CMD_USB
+-#define CONFIG_USB_STORAGE
+-#define CONFIG_USBD_HS
+-
+-#define CONFIG_CMD_USB_MASS_STORAGE
+-#define CONFIG_USB_GADGET_MASS_STORAGE
+-#define CONFIG_USB_FUNCTION_MASS_STORAGE
+-
+-#endif
+-
+-#define CONFIG_USB_GADGET_VBUS_DRAW 2
+-
+-#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
+-#define CONFIG_USB_MAX_CONTROLLER_COUNT         2
+-
+-#ifdef CONFIG_VIDEO
+-#define CONFIG_VIDEO_MXS
+-#define CONFIG_VIDEO_LOGO
+-#define CONFIG_SPLASH_SCREEN
+-#define CONFIG_SPLASH_SCREEN_ALIGN
+-#define CONFIG_CMD_BMP
+-#define CONFIG_BMP_16BPP
+-#define CONFIG_VIDEO_BMP_RLE8
+-#define CONFIG_VIDEO_BMP_LOGO
+-#define CONFIG_IMX_VIDEO_SKIP
+-#define CONFIG_RM67191
+-#endif
+-
+-#define CONFIG_BOARD_POSTCLK_INIT
+-#define CONFIG_OF_BOARD_SETUP
+#include "cpl-imx8m-mini.h"
+ 
+ #if defined(CONFIG_ANDROID_SUPPORT)
+ #include "ucm-imx8m-mini_android.h"
+-- 
+2.11.0
+
@@ -0,0 +1,577 @@
+From 684d387f307b2d6259e528eb6785d8cdead52ba5 Mon Sep 17 00:00:00 2001
+From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+Date: Mon, 19 Jul 2021 15:52:47 +0300
+Subject: [PATCH 058/126] iot-gate-imx8: Add basic support
+
+Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+---
+ arch/arm/dts/Makefile                        |   1 +
+ arch/arm/dts/iot-gate-imx8.dts               |  49 +++++
+ arch/arm/mach-imx/imx8m/Kconfig              |   7 +
+ board/compulab/iot-gate-imx8/Kconfig         |  17 ++
+ board/compulab/iot-gate-imx8/Makefile        |  15 ++
+ board/compulab/iot-gate-imx8/iot-gate-imx8.c | 265 +++++++++++++++++++++++++++
+ board/compulab/iot-gate-imx8/spl.c           |   8 +
+ configs/iot-gate-imx8_defconfig              | 102 +++++++++++
+ include/configs/iot-gate-imx8.h              |  15 ++
+ 9 files changed, 479 insertions(+)
+ create mode 100644 arch/arm/dts/iot-gate-imx8.dts
+ create mode 100644 board/compulab/iot-gate-imx8/Kconfig
+ create mode 100644 board/compulab/iot-gate-imx8/Makefile
+ create mode 100644 board/compulab/iot-gate-imx8/iot-gate-imx8.c
+ create mode 100644 board/compulab/iot-gate-imx8/spl.c
+ create mode 100644 configs/iot-gate-imx8_defconfig
+ create mode 100644 include/configs/iot-gate-imx8.h
+
+diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
+index c6b54163d0..1fc99ed1c9 100644
+--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
+@@ -890,6 +890,7 @@ dtb-$(CONFIG_ARCH_IMX8ULP) += imx8ulp-evk.dtb imx8ulp-evk-i3c.dtb
+ 
+ dtb-$(CONFIG_TARGET_UCM_IMX8M_MINI) += ucm-imx8m-mini.dtb
+ dtb-$(CONFIG_TARGET_MCM_IMX8M_MINI) += mcm-imx8m-mini.dtb
+dtb-$(CONFIG_TARGET_IOT_GATE_IMX8) += iot-gate-imx8.dtb
+ 
+ dtb-$(CONFIG_RCAR_GEN2) += \
+ 	r8a7790-lager-u-boot.dtb \
+diff --git a/arch/arm/dts/iot-gate-imx8.dts b/arch/arm/dts/iot-gate-imx8.dts
+new file mode 100644
+index 0000000000..6b6b2d69c7
+--- /dev/null
+++ b/arch/arm/dts/iot-gate-imx8.dts
+@@ -0,0 +1,49 @@
+/*
+ * Copyright 2020 CompuLab
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/dts-v1/;
+
+#include "cpl-imx8m-mini.dtsi"
+
+/ {
+	model = "CompuLab IOT-GATE-iMX8";
+	compatible = "sb-iotgimx8", "cpl,ucm-imx8m-mini", "fsl,imx8mm-evk", "fsl,imx8mm";
+
+	reg_vusb_5v: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		regulator-name = "VUSB_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+		regulator-boot-on;
+		enable-active-high;
+	};
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctl_usb_gpio>;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&iomuxc {
+	sb-iotgimx8 {
+		pinctl_usb_gpio: usb_gpio_grp {
+			fsl,pins = <
+				MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28		0x00
+			>;
+		};
+	};
+};
+diff --git a/arch/arm/mach-imx/imx8m/Kconfig b/arch/arm/mach-imx/imx8m/Kconfig
+index a38ec31d25..3102155bc1 100644
+--- a/arch/arm/mach-imx/imx8m/Kconfig
+++ b/arch/arm/mach-imx/imx8m/Kconfig
+@@ -272,6 +272,12 @@ config TARGET_MCM_IMX8M_MINI
+ 	select SUPPORT_SPL
+ 	select IMX8M_LPDDR4
+ 
+config TARGET_IOT_GATE_IMX8
+	bool "CompuLab iot-gate-imx8"
+	select IMX8MM
+	select SUPPORT_SPL
+	select IMX8M_LPDDR4
+
+ endchoice
+ 
+ source "board/freescale/imx8mq_evk/Kconfig"
+@@ -291,5 +297,6 @@ source "board/phytec/phycore_imx8mm/Kconfig"
+ source "board/phytec/phycore_imx8mp/Kconfig"
+ source "board/compulab/ucm-imx8m-mini/Kconfig"
+ source "board/compulab/mcm-imx8m-mini/Kconfig"
+source "board/compulab/iot-gate-imx8/Kconfig"
+ 
+ endif
+diff --git a/board/compulab/iot-gate-imx8/Kconfig b/board/compulab/iot-gate-imx8/Kconfig
+new file mode 100644
+index 0000000000..84f53ca6b9
+--- /dev/null
+++ b/board/compulab/iot-gate-imx8/Kconfig
+@@ -0,0 +1,17 @@
+if TARGET_IOT_GATE_IMX8
+
+config SYS_BOARD
+	default "iot-gate-imx8"
+
+config SYS_VENDOR
+	default "compulab"
+
+config SYS_CONFIG_NAME
+	default "iot-gate-imx8"
+
+config DEFAULT_DTB
+	string "U-Boot Default Device Tree File"
+	depends on TARGET_IOT_GATE_IMX8
+	default "sb-iotgimx8-can.dtb"
+
+endif
+diff --git a/board/compulab/iot-gate-imx8/Makefile b/board/compulab/iot-gate-imx8/Makefile
+new file mode 100644
+index 0000000000..af743b977b
+--- /dev/null
+++ b/board/compulab/iot-gate-imx8/Makefile
+@@ -0,0 +1,15 @@
+#
+# Copyright 2018 CompuLab
+#
+# SPDX-License-Identifier:      GPL-2.0+
+#
+
+ccflags-y += -I$(srctree)/board/compulab/plat/imx8mm/
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+else 
+obj-y += iot-gate-imx8.o
+endif
+
+obj-y += ../plat/imx8mm/
+diff --git a/board/compulab/iot-gate-imx8/iot-gate-imx8.c b/board/compulab/iot-gate-imx8/iot-gate-imx8.c
+new file mode 100644
+index 0000000000..d01b8f8767
+--- /dev/null
+++ b/board/compulab/iot-gate-imx8/iot-gate-imx8.c
+@@ -0,0 +1,265 @@
+/*
+ * Copyright 2020 CompuLab
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <errno.h>
+#include <asm/io.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm-generic/gpio.h>
+#include <fsl_esdhc.h>
+#include <mmc.h>
+#include <asm/arch/imx8mm_pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-imx/gpio.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <asm/arch/clock.h>
+#include <spl.h>
+#include <asm/mach-imx/dma.h>
+#include <power/pmic.h>
+#include <power/bd71837.h>
+#include "../common/eeprom.h"
+#include <usb.h>
+#include <asm/mach-imx/boot_mode.h>
+#include <asm/mach-imx/video.h>
+#include "ddr/ddr.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_BOARD_POSTCLK_INIT
+int board_postclk_init(void)
+{
+	/* TODO */
+	return 0;
+}
+#endif
+int board_phys_sdram_size(phys_size_t *size)
+{
+	struct lpddr4_tcm_desc *lpddr4_tcm_desc = (struct lpddr4_tcm_desc *) TCM_DATA_CFG;
+
+	switch (lpddr4_tcm_desc->size) {
+	case 4096:
+	case 2048:
+	case 1024:
+		*size = (1L << 20) * lpddr4_tcm_desc->size;
+		break;
+	default:
+		printf("%s: DRAM size %uM is not supported \n", __func__,
+				lpddr4_tcm_desc->size);
+		while ( 1 ) {};
+		break;
+	};
+	return 0;
+}
+	/* Get the top of usable RAM */
+ulong board_get_usable_ram_top(ulong total_size)
+{
+
+        if(gd->ram_top > 0x100000000)
+            gd->ram_top = 0x100000000;
+
+        return gd->ram_top;
+}
+
+int dram_init(void)
+{
+	phys_size_t sdram_size;
+	int ret;
+	ret = board_phys_sdram_size(&sdram_size);
+	printf("%s: size %llu\n", __func__, sdram_size);
+	if (ret)
+		return ret;
+
+	/* rom_pointer[1] contains the size of TEE occupies */
+	gd->ram_size = sdram_size - rom_pointer[1];
+
+	return 0;
+}
+
+#ifdef CONFIG_OF_BOARD_SETUP
+int ft_board_setup(void *blob, bd_t *bd)
+{
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_FEC_MXC
+#define FEC_RST_PAD IMX_GPIO_NR(1, 10)
+static iomux_v3_cfg_t const fec1_rst_pads[] = {
+	IMX8MM_PAD_GPIO1_IO10_GPIO1_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_iomux_fec(void)
+{
+	imx_iomux_v3_setup_multiple_pads(fec1_rst_pads,
+					 ARRAY_SIZE(fec1_rst_pads));
+
+	gpio_request(FEC_RST_PAD, "fec1_rst");
+	gpio_direction_output(FEC_RST_PAD, 0);
+	udelay(500);
+	gpio_direction_output(FEC_RST_PAD, 1);
+}
+
+/*
+ * setup_mac_address() - set Ethernet MAC address environment.
+ *
+ * @return: 0 on success, -1 on failure
+ */
+static int setup_mac_address(void)
+{
+        int ret;
+        unsigned char enetaddr[6];
+
+        ret = eth_env_get_enetaddr("ethaddr", enetaddr);
+        if (ret)
+                return 0;
+
+        ret = cl_eeprom_read_mac_addr(enetaddr, CONFIG_SYS_I2C_EEPROM_BUS);
+        if (ret)
+                return ret;
+
+        ret = is_valid_ethaddr(enetaddr);
+        if (!ret)
+                return -1;
+
+	ret = eth_env_set_enetaddr("ethaddr", enetaddr);
+	if (ret)
+		return -1;
+
+        return 0;
+}
+
+static int setup_fec(void)
+{
+	struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
+		= (struct iomuxc_gpr_base_regs *) IOMUXC_GPR_BASE_ADDR;
+
+	setup_iomux_fec();
+
+	/* Use 125M anatop REF_CLK1 for ENET1, not from external */
+	clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
+			IOMUXC_GPR_GPR1_GPR_ENET1_TX_CLK_SEL_SHIFT, 0);
+	return set_clk_enet(ENET_125MHZ);
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	/* enable rgmii rxc skew and phy mode select to RGMII copper */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
+
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x00);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x82ee);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+	return 0;
+}
+#endif
+
+int board_usb_init(int index, enum usb_init_type init)
+{
+	debug("board_usb_init %d, type %d\n", index, init);
+
+	imx8m_usb_power(index, true);
+
+	return 0;
+}
+
+int board_usb_cleanup(int index, enum usb_init_type init)
+{
+	debug("board_usb_cleanup %d, type %d\n", index, init);
+
+	imx8m_usb_power(index, false);
+
+	return 0;
+}
+int board_init(void)
+{
+
+#ifdef CONFIG_FEC_MXC
+	setup_fec();
+#endif
+	return 0;
+}
+
+int board_mmc_get_env_dev(int devno)
+{
+	const ulong user_env_devno = env_get_hex("env_dev", ULONG_MAX);
+	if (user_env_devno != ULONG_MAX) {
+		printf("User Environment dev# is (%lu)\n", user_env_devno);
+		return (int)user_env_devno;
+	}
+	return devno;
+}
+
+static int _mmc_get_env_part(void)
+{
+	const ulong user_env_part = env_get_hex("env_part", ULONG_MAX);
+	if (user_env_part != ULONG_MAX) {
+		printf("User Environment part# is (%lu)\n", user_env_part);
+		return (int)user_env_part;
+	}
+	return CONFIG_SYS_MMC_ENV_PART;
+}
+
+uint mmc_get_env_part(struct mmc *mmc)
+{
+	if (mmc->part_support)
+	    return _mmc_get_env_part();
+
+	return 0;
+}
+
+int mmc_map_to_kernel_blk(int devno){
+	return devno;
+}
+
+static void board_bootdev_init(void)
+{
+	u32 bootdev = get_boot_device();
+	switch (bootdev) {
+	case MMC3_BOOT:
+		bootdev = 2;
+		break;
+	case SD2_BOOT:
+		bootdev = 1;
+		break;
+	default:
+		env_set("bootdev", NULL);
+		return;
+	}
+	env_set_ulong("bootdev", bootdev);
+}
+
+int board_late_init(void)
+{
+	int ret;
+
+#ifdef CONFIG_ENV_IS_IN_MMC
+	board_late_mmc_env_init();
+	board_bootdev_init();
+#endif
+
+	ret = setup_mac_address();
+	if (ret < 0)
+		printf("%s: Can't set MAC address\n", __func__);
+
+	return 0;
+}
+
+#ifdef CONFIG_FSL_FASTBOOT
+#ifdef CONFIG_ANDROID_RECOVERY
+int is_recovery_key_pressing(void)
+{
+	return 0; /*TODO*/
+}
+#endif /*CONFIG_ANDROID_RECOVERY*/
+#endif /*CONFIG_FSL_FASTBOOT*/
+diff --git a/board/compulab/iot-gate-imx8/spl.c b/board/compulab/iot-gate-imx8/spl.c
+new file mode 100644
+index 0000000000..6488770333
+--- /dev/null
+++ b/board/compulab/iot-gate-imx8/spl.c
+@@ -0,0 +1,8 @@
+#include <asm/io.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/arch/imx8mm_pins.h>
+#include <asm/arch/clock.h>
+
+int spl_board_private_init(void) {
+	return 0;
+}
+diff --git a/configs/iot-gate-imx8_defconfig b/configs/iot-gate-imx8_defconfig
+new file mode 100644
+index 0000000000..39c448eca0
+--- /dev/null
+++ b/configs/iot-gate-imx8_defconfig
+@@ -0,0 +1,102 @@
+CONFIG_ARM=y
+CONFIG_SPL_SYS_ICACHE_OFF=y
+CONFIG_SPL_SYS_DCACHE_OFF=y
+CONFIG_ARCH_IMX8M=y
+CONFIG_SYS_TEXT_BASE=0x40200000
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_ENV_SIZE=0x1000
+CONFIG_ENV_OFFSET=0x4400
+CONFIG_DM_GPIO=y
+CONFIG_TARGET_IOT_GATE_IMX8=y
+CONFIG_DEFAULT_DTB="sb-iotgimx8-can.dtb"
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL=y
+CONFIG_CSF_SIZE=0x2000
+CONFIG_SPL_TEXT_BASE=0x7E1000
+CONFIG_LOCALVERSION="-iot-gate-imx8-1.0"
+CONFIG_FIT=y
+CONFIG_FIT_EXTERNAL_OFFSET=0x3000
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
+CONFIG_OF_SYSTEM_SETUP=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/imx8m/imximage-8mm-lpddr4.cfg"
+CONFIG_CONSOLE_MUX=y
+CONFIG_DEFAULT_FDT_FILE="sb-iotgimx8-can.dtb"
+CONFIG_BOARD_LATE_INIT=y
+CONFIG_ARCH_MISC_INIT=y
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_SPL_BOARD_INIT=y
+CONFIG_SPL_SEPARATE_BSS=y
+CONFIG_SPL_POWER_SUPPORT=y
+CONFIG_HUSH_PARSER=y
+CONFIG_SYS_PROMPT="u-boot=> "
+# CONFIG_BOOTM_NETBSD is not set
+CONFIG_CMD_EEPROM=y
+CONFIG_CMD_EEPROM_LAYOUT=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_CLK=y
+CONFIG_CMD_FUSE=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_EFI_PARTITION=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="iot-gate-imx8"
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_CLK_COMPOSITE_CCF=y
+CONFIG_CLK_IMX8MM=y
+CONFIG_MXC_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MXC=y
+CONFIG_DM_MMC=y
+CONFIG_SUPPORT_EMMC_BOOT=y
+CONFIG_MMC_IO_VOLTAGE=y
+CONFIG_MMC_UHS_SUPPORT=y
+CONFIG_MMC_HS400_ES_SUPPORT=y
+CONFIG_MMC_HS400_SUPPORT=y
+CONFIG_FSL_ESDHC_IMX=y
+CONFIG_DM_ETH=y
+CONFIG_FEC_MXC=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX8M=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_DM_RESET=y
+CONFIG_MXC_UART=y
+CONFIG_SYSRESET=y
+CONFIG_SYSRESET_PSCI=y
+CONFIG_DM_THERMAL=y
+CONFIG_NXP_TMU=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="FSL"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_CI_UDC=y
+CONFIG_SDP_LOADADDR=0x40400000
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX88179=y
+CONFIG_EXT4_WRITE=y
+CONFIG_FAT_WRITE=y
+CONFIG_OF_LIBFDT_OVERLAY=y
+# CONFIG_EFI_LOADER is not set
+diff --git a/include/configs/iot-gate-imx8.h b/include/configs/iot-gate-imx8.h
+new file mode 100644
+index 0000000000..b3d6082a66
+--- /dev/null
+++ b/include/configs/iot-gate-imx8.h
+@@ -0,0 +1,15 @@
+/*
+ * Copyright 2020 CompuLab
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __UCM_IMX8M_MINI_H
+#define __UCM_IMX8M_MINI_H
+
+#include "cpl-imx8m-mini.h"
+
+#if defined(CONFIG_ANDROID_SUPPORT)
+#include "ucm-imx8m-mini_android.h"
+#endif
+#endif
+-- 
+2.11.0
+
@@ -0,0 +1,28 @@
+From 94829c14ef32f7d41ac3b5b5efee763c549ff196 Mon Sep 17 00:00:00 2001
+From: Valentin Raevsky <valentin@compulab.co.il>
+Date: Wed, 15 Jul 2020 15:25:04 +0300
+Subject: [PATCH 059/126] mcm-imx8m-mini: config: Update env size/offest
+
+Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
+---
+ configs/mcm-imx8m-mini_defconfig | 4 ++--
+ 1 file changed, 2 insertions(+), 2 deletions(-)
+
+diff --git a/configs/mcm-imx8m-mini_defconfig b/configs/mcm-imx8m-mini_defconfig
+index a4c3c90f83..971e1ec982 100644
+--- a/configs/mcm-imx8m-mini_defconfig
+++ b/configs/mcm-imx8m-mini_defconfig
+@@ -4,8 +4,8 @@ CONFIG_SPL_SYS_DCACHE_OFF=y
+ CONFIG_ARCH_IMX8M=y
+ CONFIG_SYS_TEXT_BASE=0x40200000
+ CONFIG_SPL_GPIO_SUPPORT=y
+-CONFIG_ENV_SIZE=0x4000
+-CONFIG_ENV_OFFSET=0x1000
+CONFIG_ENV_SIZE=0x1000
+CONFIG_ENV_OFFSET=0x4400
+ CONFIG_DM_GPIO=y
+ CONFIG_TARGET_MCM_IMX8M_MINI=y
+ CONFIG_SPL_MMC_SUPPORT=y
+-- 
+2.11.0
+
@@ -0,0 +1,29 @@
+From e94a6f8fef7c25d00a41f791ab16813fc760c392 Mon Sep 17 00:00:00 2001
+From: Valentin Raevsky <valentin@compulab.co.il>
+Date: Wed, 15 Jul 2020 15:27:37 +0300
+Subject: [PATCH 060/126] imx8m-mini: env: config: Update size/offset value
+
+Update size/offset value for CompuLab imx8m-mini boards
+
+Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
+---
+ tools/env/fw_env.config | 6 +++---
+ 1 file changed, 3 insertions(+), 3 deletions(-)
+
+diff --git a/tools/env/fw_env.config b/tools/env/fw_env.config
+index 3222fd715c..988ef9f728 100644
+--- a/tools/env/fw_env.config
+++ b/tools/env/fw_env.config
+@@ -6,6 +6,6 @@
+ # be the same as the Environment size, which is valid for NOR and SPI-dataflash
+ # Device offset must be prefixed with 0x to be parsed as a hexadecimal value.
+ 
+-# Block device for mcm-imx8m-mini
+-/dev/mmcblk2boot0	0x1000	0x4000
+-#/dev/mmcblk1		0x1000	0x4000
+# Block devices for CompuLab imx8m-mini
+/dev/mmcblk2boot0	0x4400	0x1000
+#/dev/mmcblk1		0x4400	0x1000
+-- 
+2.11.0
+
@@ -0,0 +1,123 @@
+From 663f170f28034023bbd13d6c4359be43719862e7 Mon Sep 17 00:00:00 2001
+From: Valentin Raevsky <valentin@compulab.co.il>
+Date: Fri, 17 Jul 2020 18:59:22 +0300
+Subject: [PATCH 061/126] imx8: eeprom: Move to the imx8 platform independent
+ folder
+
+Move the eeprom code the imx8 platform independent folder.
+The same code gets used by all CompuLab imx8 boards.
+
+Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
+---
+ board/compulab/iot-gate-imx8/Makefile                    | 2 ++
+ board/compulab/mcm-imx8m-mini/Makefile                   | 2 ++
+ board/compulab/plat/imx8/Makefile                        | 1 +
+ board/compulab/plat/{imx8mm => imx8}/eeprom/Makefile     | 0
+ board/compulab/plat/{imx8mm => imx8}/eeprom/eeprom.c     | 0
+ board/compulab/plat/{imx8mm => imx8}/eeprom/eeprom.h     | 0
+ board/compulab/plat/{imx8mm => imx8}/eeprom/eeprom_spl.c | 1 +
+ board/compulab/plat/imx8mm/Makefile                      | 1 -
+ board/compulab/ucm-imx8m-mini/Makefile                   | 2 ++
+ 9 files changed, 8 insertions(+), 1 deletion(-)
+ create mode 100644 board/compulab/plat/imx8/Makefile
+ rename board/compulab/plat/{imx8mm => imx8}/eeprom/Makefile (100%)
+ rename board/compulab/plat/{imx8mm => imx8}/eeprom/eeprom.c (100%)
+ rename board/compulab/plat/{imx8mm => imx8}/eeprom/eeprom.h (100%)
+ rename board/compulab/plat/{imx8mm => imx8}/eeprom/eeprom_spl.c (99%)
+
+diff --git a/board/compulab/iot-gate-imx8/Makefile b/board/compulab/iot-gate-imx8/Makefile
+index af743b977b..e5239d1dbb 100644
+--- a/board/compulab/iot-gate-imx8/Makefile
+++ b/board/compulab/iot-gate-imx8/Makefile
+@@ -5,6 +5,7 @@
+ #
+ 
+ ccflags-y += -I$(srctree)/board/compulab/plat/imx8mm/
+ccflags-y += -I$(srctree)/board/compulab/plat/imx8/
+ 
+ ifdef CONFIG_SPL_BUILD
+ obj-y += spl.o
+@@ -13,3 +14,4 @@ obj-y += iot-gate-imx8.o
+ endif
+ 
+ obj-y += ../plat/imx8mm/
+obj-y += ../plat/imx8/
+diff --git a/board/compulab/mcm-imx8m-mini/Makefile b/board/compulab/mcm-imx8m-mini/Makefile
+index 9ce2875d6e..2cadd46fb8 100644
+--- a/board/compulab/mcm-imx8m-mini/Makefile
+++ b/board/compulab/mcm-imx8m-mini/Makefile
+@@ -5,6 +5,7 @@
+ #
+ 
+ ccflags-y += -I$(srctree)/board/compulab/plat/imx8mm/
+ccflags-y += -I$(srctree)/board/compulab/plat/imx8/
+ 
+ ifdef CONFIG_SPL_BUILD
+ obj-y += spl.o
+@@ -13,3 +14,4 @@ obj-y += mcm-imx8m-mini.o
+ endif
+ 
+ obj-y += ../plat/imx8mm/
+obj-y += ../plat/imx8/
+diff --git a/board/compulab/plat/imx8/Makefile b/board/compulab/plat/imx8/Makefile
+new file mode 100644
+index 0000000000..9d3044cb9e
+--- /dev/null
+++ b/board/compulab/plat/imx8/Makefile
+@@ -0,0 +1 @@
+obj-y += eeprom/
+diff --git a/board/compulab/plat/imx8mm/eeprom/Makefile b/board/compulab/plat/imx8/eeprom/Makefile
+similarity index 100%
+rename from board/compulab/plat/imx8mm/eeprom/Makefile
+rename to board/compulab/plat/imx8/eeprom/Makefile
+diff --git a/board/compulab/plat/imx8mm/eeprom/eeprom.c b/board/compulab/plat/imx8/eeprom/eeprom.c
+similarity index 100%
+rename from board/compulab/plat/imx8mm/eeprom/eeprom.c
+rename to board/compulab/plat/imx8/eeprom/eeprom.c
+diff --git a/board/compulab/plat/imx8mm/eeprom/eeprom.h b/board/compulab/plat/imx8/eeprom/eeprom.h
+similarity index 100%
+rename from board/compulab/plat/imx8mm/eeprom/eeprom.h
+rename to board/compulab/plat/imx8/eeprom/eeprom.h
+diff --git a/board/compulab/plat/imx8mm/eeprom/eeprom_spl.c b/board/compulab/plat/imx8/eeprom/eeprom_spl.c
+similarity index 99%
+rename from board/compulab/plat/imx8mm/eeprom/eeprom_spl.c
+rename to board/compulab/plat/imx8/eeprom/eeprom_spl.c
+index 09a04fda92..f25493b1ee 100644
+--- a/board/compulab/plat/imx8mm/eeprom/eeprom_spl.c
+++ b/board/compulab/plat/imx8/eeprom/eeprom_spl.c
+@@ -7,6 +7,7 @@
+ #include <common.h>
+ #include <i2c.h>
+ #include <linux/kernel.h>
+#include <linux/delay.h>
+ #include <asm/arch/imx8mq_pins.h>
+ #include <asm/mach-imx/gpio.h>
+ #include <asm-generic/gpio.h>
+diff --git a/board/compulab/plat/imx8mm/Makefile b/board/compulab/plat/imx8mm/Makefile
+index 2f68e0523e..33b3fedef9 100644
+--- a/board/compulab/plat/imx8mm/Makefile
+++ b/board/compulab/plat/imx8mm/Makefile
+@@ -1,3 +1,2 @@
+ obj-y += ddr/
+-obj-y += eeprom/
+ obj-y += spl/
+diff --git a/board/compulab/ucm-imx8m-mini/Makefile b/board/compulab/ucm-imx8m-mini/Makefile
+index dbde2116cd..870792441c 100644
+--- a/board/compulab/ucm-imx8m-mini/Makefile
+++ b/board/compulab/ucm-imx8m-mini/Makefile
+@@ -5,6 +5,7 @@
+ #
+ 
+ ccflags-y += -I$(srctree)/board/compulab/plat/imx8mm/
+ccflags-y += -I$(srctree)/board/compulab/plat/imx8/
+ 
+ ifdef CONFIG_SPL_BUILD
+ obj-y += spl.o
+@@ -13,3 +14,4 @@ obj-y += ucm-imx8m-mini.o
+ endif
+ 
+ obj-y += ../plat/imx8mm/
+obj-y += ../plat/imx8/
+-- 
+2.11.0
+
@@ -0,0 +1,285 @@
+From bac8699e303c75526c30e3e850601c39944dad8a Mon Sep 17 00:00:00 2001
+From: Valentin Raevsky <valentin@compulab.co.il>
+Date: Sat, 18 Jul 2020 13:02:39 +0300
+Subject: [PATCH 062/126] imx8: eeprom: Remove duplicated code
+
+Remove duplicated code.
+Leave the i2c spl helper only for use in the ddr discovery.
+
+Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
+---
+ board/compulab/plat/imx8/eeprom/Makefile     |   4 -
+ board/compulab/plat/imx8/eeprom/eeprom.c     | 192 ---------------------------
+ board/compulab/plat/imx8/eeprom/eeprom.h     |  30 -----
+ board/compulab/plat/imx8/eeprom/eeprom_spl.c |   5 +-
+ 4 files changed, 4 insertions(+), 227 deletions(-)
+ delete mode 100644 board/compulab/plat/imx8/eeprom/eeprom.c
+ delete mode 100644 board/compulab/plat/imx8/eeprom/eeprom.h
+
+diff --git a/board/compulab/plat/imx8/eeprom/Makefile b/board/compulab/plat/imx8/eeprom/Makefile
+index 9ec4d29dc1..62ee6de6fa 100644
+--- a/board/compulab/plat/imx8/eeprom/Makefile
+++ b/board/compulab/plat/imx8/eeprom/Makefile
+@@ -1,5 +1 @@
+-ifdef CONFIG_SPL_BUILD
+ obj-y += eeprom_spl.o
+-else
+-obj-y += eeprom.o
+-endif
+diff --git a/board/compulab/plat/imx8/eeprom/eeprom.c b/board/compulab/plat/imx8/eeprom/eeprom.c
+deleted file mode 100644
+index fd1fa49e21..0000000000
+--- a/board/compulab/plat/imx8/eeprom/eeprom.c
+++ /dev/null
+@@ -1,192 +0,0 @@
+-/*
+- * (C) Copyright 2011 CompuLab, Ltd. <www.compulab.co.il>
+- *
+- * SPDX-License-Identifier:	GPL-2.0+
+- */
+-
+-#include <common.h>
+-#include <dm.h>
+-#include <i2c.h>
+-#include <eeprom_layout.h>
+-#include <eeprom_field.h>
+-#include <linux/kernel.h>
+-#include <asm/setup.h>
+-
+-#ifndef CONFIG_SYS_I2C_EEPROM_ADDR
+-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
+-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+-#endif
+-
+-#ifndef CONFIG_SYS_I2C_EEPROM_BUS
+-#define CONFIG_SYS_I2C_EEPROM_BUS	1
+-#endif
+-
+-#define EEPROM_LAYOUT_VER_OFFSET	44
+-#define BOARD_SERIAL_OFFSET		20
+-#define BOARD_SERIAL_OFFSET_LEGACY	8
+-#define BOARD_REV_OFFSET		0
+-#define BOARD_REV_OFFSET_LEGACY		6
+-#define BOARD_REV_SIZE			2
+-#define PRODUCT_NAME_OFFSET		128
+-#define PRODUCT_NAME_SIZE		16
+-#define MAC_ADDR_OFFSET			4
+-#define MAC_ADDR_OFFSET_LEGACY		0
+-
+-#define LAYOUT_INVALID	0
+-#define LAYOUT_LEGACY	0xff
+-
+-static int cpl_eeprom_bus;
+-static int cpl_eeprom_layout;
+-
+-static struct udevice  *g_dev = NULL;
+-
+-static int cpl_eeprom_init(void) {
+-
+-	int i2c_bus = CONFIG_SYS_I2C_EEPROM_BUS;
+-	uint8_t chip = CONFIG_SYS_I2C_EEPROM_ADDR;
+-
+-	struct udevice *bus, *dev;
+-	int ret;
+-
+-	if (!g_dev) {
+-
+-		ret = uclass_get_device_by_seq(UCLASS_I2C, i2c_bus, &bus);
+-		if (ret) {
+-			printf("%s: No bus %d\n", __func__, i2c_bus);
+-			return ret;
+-		}
+-
+-		ret = dm_i2c_probe(bus, chip, 0, &dev);
+-		if (ret) {
+-			printf("%s: Can't find device id=0x%x, on bus %d\n",
+-				__func__, chip, i2c_bus);
+-			return ret;
+-		}
+-
+-		/* Init */
+-		g_dev = dev;
+-	}
+-
+-	return 0;
+-}
+-
+-static int cpl_eeprom_read(uint offset, uchar *buf, int len)
+-{
+-	int res;
+-
+-	res = cpl_eeprom_init();
+-	if (res < 0)
+-		return res;
+-
+-	res  = dm_i2c_read(g_dev, offset, buf, len);
+-
+-	return res;
+-}
+-
+-
+-static int cpl_eeprom_setup(uint eeprom_bus)
+-{
+-	int res;
+-
+-	/*
+-	 * We know the setup was already done when the layout is set to a valid
+-	 * value and we're using the same bus as before.
+-	 */
+-	if (cpl_eeprom_layout != LAYOUT_INVALID && eeprom_bus == cpl_eeprom_bus)
+-		return 0;
+-
+-	cpl_eeprom_bus = eeprom_bus;
+-	res = cpl_eeprom_read(EEPROM_LAYOUT_VER_OFFSET,
+-			     (uchar *)&cpl_eeprom_layout, 1);
+-
+-	if (res) {
+-		cpl_eeprom_layout = LAYOUT_INVALID;
+-		return res;
+-	}
+-
+-	if (cpl_eeprom_layout == 0 || cpl_eeprom_layout >= 0x20)
+-		cpl_eeprom_layout = LAYOUT_LEGACY;
+-
+-	return 0;
+-}
+-
+-/*
+- * Routine: cpl_eeprom_read_mac_addr
+- * Description: read mac address and store it in buf.
+- */
+-int cpl_eeprom_read_mac_addr(uchar *buf, uint eeprom_bus)
+-{
+-	uint offset;
+-	int err;
+-
+-	err = cpl_eeprom_setup(eeprom_bus);
+-	if (err)
+-		return err;
+-
+-	offset = (cpl_eeprom_layout != LAYOUT_LEGACY) ?
+-			MAC_ADDR_OFFSET : MAC_ADDR_OFFSET_LEGACY;
+-
+-	return cpl_eeprom_read(offset, buf, 6);
+-}
+-
+-static u32 board_rev;
+-
+-/*
+- * Routine: cpl_eeprom_get_board_rev
+- * Description: read system revision from eeprom
+- */
+-u32 cpl_eeprom_get_board_rev(uint eeprom_bus)
+-{
+-	char str[5]; /* Legacy representation can contain at most 4 digits */
+-	uint offset = BOARD_REV_OFFSET_LEGACY;
+-
+-	if (board_rev)
+-		return board_rev;
+-
+-	if (cpl_eeprom_setup(eeprom_bus))
+-		return 0;
+-
+-	if (cpl_eeprom_layout != LAYOUT_LEGACY)
+-		offset = BOARD_REV_OFFSET;
+-
+-	if (cpl_eeprom_read(offset, (uchar *)&board_rev, BOARD_REV_SIZE))
+-		return 0;
+-
+-	/*
+-	 * Convert legacy syntactic representation to semantic
+-	 * representation. i.e. for rev 1.00: 0x100 --> 0x64
+-	 */
+-	if (cpl_eeprom_layout == LAYOUT_LEGACY) {
+-		sprintf(str, "%x", board_rev);
+-		board_rev = simple_strtoul(str, NULL, 10);
+-	}
+-
+-	return board_rev;
+-};
+-
+-/*
+- * Routine: cpl_eeprom_get_board_rev
+- * Description: read system revision from eeprom
+- *
+- * @buf: buffer to store the product name
+- * @eeprom_bus: i2c bus num of the eeprom
+- *
+- * @return: 0 on success, < 0 on failure
+- */
+-int cpl_eeprom_get_product_name(uchar *buf, uint eeprom_bus)
+-{
+-	int err;
+-
+-	if (buf == NULL)
+-		return -EINVAL;
+-
+-	err = cpl_eeprom_setup(eeprom_bus);
+-	if (err)
+-		return err;
+-
+-	err = cpl_eeprom_read(PRODUCT_NAME_OFFSET, buf, PRODUCT_NAME_SIZE);
+-	if (!err) /* Protect ourselves from invalid data (unterminated str) */
+-		buf[PRODUCT_NAME_SIZE - 1] = '\0';
+-
+-	return err;
+-}
+diff --git a/board/compulab/plat/imx8/eeprom/eeprom.h b/board/compulab/plat/imx8/eeprom/eeprom.h
+deleted file mode 100644
+index 9de4aadd43..0000000000
+--- a/board/compulab/plat/imx8/eeprom/eeprom.h
+++ /dev/null
+@@ -1,30 +0,0 @@
+-/*
+- * (C) Copyright 2011 CompuLab, Ltd. <www.compulab.co.il>
+- *
+- * SPDX-License-Identifier:	GPL-2.0+
+- */
+-
+-#ifndef _EEPROM_
+-#define _EEPROM_
+-#include <errno.h>
+-
+-#ifdef CONFIG_DM_I2C
+-int cpl_eeprom_read_mac_addr(uchar *buf, uint eeprom_bus);
+-u32 cpl_eeprom_get_board_rev(uint eeprom_bus);
+-int cpl_eeprom_get_product_name(uchar *buf, uint eeprom_bus);
+-#else
+-static inline int cpl_eeprom_read_mac_addr(uchar *buf, uint eeprom_bus)
+-{
+-	return 1;
+-}
+-static inline u32 cpl_eeprom_get_board_rev(uint eeprom_bus)
+-{
+-	return 0;
+-}
+-static inline int cpl_eeprom_get_product_name(uchar *buf, uint eeprom_bus)
+-{
+-	return -ENOSYS;
+-}
+-#endif
+-
+-#endif
+diff --git a/board/compulab/plat/imx8/eeprom/eeprom_spl.c b/board/compulab/plat/imx8/eeprom/eeprom_spl.c
+index f25493b1ee..79b2e29c63 100644
+--- a/board/compulab/plat/imx8/eeprom/eeprom_spl.c
+++ b/board/compulab/plat/imx8/eeprom/eeprom_spl.c
+@@ -12,7 +12,8 @@
+ #include <asm/mach-imx/gpio.h>
+ #include <asm-generic/gpio.h>
+ #include <asm/setup.h>
+-#include "eeprom.h"
+
+#ifdef CONFIG_SPL_BUILD
+ 
+ #define CONFIG_SYS_I2C_EEPROM_ADDR_P1	0x51
+ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+@@ -146,3 +147,5 @@ u32 cl_eeprom_set_osize(u32 osize)
+ 
+ 	return board_osize;
+ };
+
+#endif
+-- 
+2.11.0
+
@@ -0,0 +1,100 @@
+From eb1947cb1550fdcb8e41364f2e9b3e9deab974b5 Mon Sep 17 00:00:00 2001
+From: Valentin Raevsky <valentin@compulab.co.il>
+Date: Mon, 20 Jul 2020 06:08:58 +0300
+Subject: [PATCH 064/126] imx8m-mini: Refactor the usdhc2
+
+1) Make it removable.
+2) Disable 1V8.
+3) Fix the card detect in spl and u-boot.
+
+Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
+---
+ arch/arm/dts/cpl-imx8m-mini.dtsi     |  5 +++--
+ board/compulab/plat/imx8mm/spl/spl.c | 26 ++++----------------------
+ 2 files changed, 7 insertions(+), 24 deletions(-)
+
+diff --git a/arch/arm/dts/cpl-imx8m-mini.dtsi b/arch/arm/dts/cpl-imx8m-mini.dtsi
+index 3fe1e7ac5f..4f9c5fbfb9 100644
+--- a/arch/arm/dts/cpl-imx8m-mini.dtsi
+++ b/arch/arm/dts/cpl-imx8m-mini.dtsi
+@@ -125,7 +125,7 @@
+ 
+ 		pinctrl_usdhc2_gpio: usdhc2grpgpio {
+ 			fsl,pins = <
+-				MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
+				MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12	0x41
+ 				MX8MM_IOMUXC_SD2_WP_USDHC2_WP		0
+ 			>;
+ 		};
+@@ -426,10 +426,11 @@
+ 	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ 	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ 	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ 	bus-width = <4>;
+ 	fsl,wp-controller;
+-	non-removable;
+ 	vmmc-supply = <&reg_usdhc2_vmmc>;
+	no-1-8-v;
+ 	status = "okay";
+ };
+ 
+diff --git a/board/compulab/plat/imx8mm/spl/spl.c b/board/compulab/plat/imx8mm/spl/spl.c
+index 50aa6bea3f..643093aaf9 100644
+--- a/board/compulab/plat/imx8mm/spl/spl.c
+++ b/board/compulab/plat/imx8mm/spl/spl.c
+@@ -55,7 +55,7 @@ struct i2c_pads_info i2c_pad_info1 = {
+ 	},
+ };
+ 
+-#define USDHC2_CD_GPIO	IMX_GPIO_NR(2, 18)
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(2, 12)
+ #define USDHC2_PWR_GPIO IMX_GPIO_NR(2, 19)
+ 
+ #define USDHC_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE |PAD_CTL_PE | \
+@@ -83,20 +83,9 @@ static iomux_v3_cfg_t const usdhc2_pads[] = {
+ 	IMX8MM_PAD_SD2_DATA2_USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ 	IMX8MM_PAD_SD2_DATA3_USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ 	IMX8MM_PAD_SD2_RESET_B_GPIO2_IO19 | MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL),
+	IMX8MM_PAD_SD2_CD_B_GPIO2_IO12 | MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL),
+ };
+ 
+-/*
+- * The evk board uses DAT3 to detect CD card plugin,
+- * in u-boot we mux the pin to GPIO when doing board_mmc_getcd.
+- */
+-static iomux_v3_cfg_t const usdhc2_cd_pad =
+-	IMX8MM_PAD_SD2_DATA3_GPIO2_IO18 | MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL);
+-
+-static iomux_v3_cfg_t const usdhc2_dat3_pad =
+-	IMX8MM_PAD_SD2_DATA3_USDHC2_DATA3 |
+-	MUX_PAD_CTRL(USDHC_PAD_CTRL);
+-
+-
+ static struct fsl_esdhc_cfg usdhc_cfg[2] = {
+ 	{USDHC2_BASE_ADDR, 0, 4},
+ 	{USDHC3_BASE_ADDR, 0, 8},
+@@ -153,18 +142,11 @@ int board_mmc_getcd(struct mmc *mmc)
+ 		ret = 1;
+ 		break;
+ 	case USDHC2_BASE_ADDR:
+-		imx_iomux_v3_setup_pad(usdhc2_cd_pad);
+ 		gpio_request(USDHC2_CD_GPIO, "usdhc2 cd");
+ 		gpio_direction_input(USDHC2_CD_GPIO);
+-
+-		/*
+-		 * Since it is the DAT3 pin, this pin is pulled to
+-		 * low voltage if no card
+-		 */
+ 		ret = gpio_get_value(USDHC2_CD_GPIO);
+-
+-		imx_iomux_v3_setup_pad(usdhc2_dat3_pad);
+-		return ret;
+		/* CD is active low */
+		return !ret;
+ 	}
+ 
+ 	return 1;
+-- 
+2.11.0
+
@@ -0,0 +1,46 @@
+From c8f58be8401b672be8aa35226470ffd2da136364 Mon Sep 17 00:00:00 2001
+From: Valentin Raevsky <valentin@compulab.co.il>
+Date: Mon, 20 Jul 2020 06:29:03 +0300
+Subject: [PATCH 065/126] mcm-imx8m-mini: reset: Refactor the reset
+
+Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
+---
+ board/compulab/plat/imx8mm/spl/spl.c | 9 ---------
+ configs/mcm-imx8m-mini_defconfig     | 3 ---
+ 2 files changed, 12 deletions(-)
+
+diff --git a/board/compulab/plat/imx8mm/spl/spl.c b/board/compulab/plat/imx8mm/spl/spl.c
+index 643093aaf9..ad1be9befd 100644
+--- a/board/compulab/plat/imx8mm/spl/spl.c
+++ b/board/compulab/plat/imx8mm/spl/spl.c
+@@ -251,12 +251,3 @@ void board_init_f(ulong dummy)
+ 
+ 	board_init_r(NULL, 0);
+ }
+-
+-int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+-{
+-	puts ("resetting ...\n");
+-
+-	reset_cpu(WDOG1_BASE_ADDR);
+-
+-	return 0;
+-}
+diff --git a/configs/mcm-imx8m-mini_defconfig b/configs/mcm-imx8m-mini_defconfig
+index 971e1ec982..e0e4f86329 100644
+--- a/configs/mcm-imx8m-mini_defconfig
+++ b/configs/mcm-imx8m-mini_defconfig
+@@ -77,10 +77,7 @@ CONFIG_PINCTRL_IMX8M=y
+ CONFIG_DM_REGULATOR=y
+ CONFIG_DM_REGULATOR_FIXED=y
+ CONFIG_DM_REGULATOR_GPIO=y
+-CONFIG_DM_RESET=y
+ CONFIG_MXC_UART=y
+-CONFIG_SYSRESET=y
+-CONFIG_SYSRESET_PSCI=y
+ CONFIG_DM_THERMAL=y
+ CONFIG_NXP_TMU=y
+ CONFIG_USB=y
+-- 
+2.11.0
+
@@ -0,0 +1,36 @@
+From 0a9c14878c90919628fa76ca098f18c86c06cf97 Mon Sep 17 00:00:00 2001
+From: Valentin Raevsky <valentin@compulab.co.il>
+Date: Mon, 20 Jul 2020 13:01:28 +0300
+Subject: [PATCH 066/126] imx8m-mini: ddr: Change the memory presets order
+
+Make the simplest one 1-st.
+Nanya 1G has the best ddr-phy settings for reading the mr4-mr8 registers.
+
+Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
+---
+ board/compulab/plat/imx8mm/ddr/ddr.c | 8 ++++----
+ 1 file changed, 4 insertions(+), 4 deletions(-)
+
+diff --git a/board/compulab/plat/imx8mm/ddr/ddr.c b/board/compulab/plat/imx8mm/ddr/ddr.c
+index 1340475bef..4d774835ef 100644
+--- a/board/compulab/plat/imx8mm/ddr/ddr.c
+++ b/board/compulab/plat/imx8mm/ddr/ddr.c
+@@ -63,11 +63,11 @@ struct lpddr4_desc {
+ 
+ #define DEFAULT (('D' << 24) + ('E' << 16 ) + ( 'F' << 8 ) + 'A')
+ static const struct lpddr4_desc lpddr4_array[] = {
+-	{ .name = "Micron", .id = 0xff020008, .size = 2048, .count = 1, .timing = &ucm_dram_timing_ff020008}, //Only the first timing entry is in use
+-	{ .name = "Micron", .id = 0xff000110, .size = 4096, .count = 1, .timing = &ucm_dram_timing_ff000110},
+-	{ .name = "Samsung",.id = 0x01061010, .size = 2048, .count = 1, .timing = &ucm_dram_timing_01061010},
+	{ .name = "Nanya",  .id = 0x01050008, .size = 1024, .count = 1, .timing = &ucm_dram_timing_01050008}, //Only the first timing entry is in use
+ 	{ .name = "Nanya",  .id = 0x05000010, .size = 2048, .count = 1, .timing = &ucm_dram_timing_01061010},
+-	{ .name = "Nanya",  .id = 0x01050008, .size = 1024, .count = 1, .timing = &ucm_dram_timing_01050008},
+	{ .name = "Samsung",.id = 0x01061010, .size = 2048, .count = 1, .timing = &ucm_dram_timing_01061010},
+	{ .name = "Micron", .id = 0xff020008, .size = 2048, .count = 1, .timing = &ucm_dram_timing_ff020008},
+	{ .name = "Micron", .id = 0xff000110, .size = 4096, .count = 1, .timing = &ucm_dram_timing_ff000110},
+ };
+ 
+ static unsigned int lpddr4_get_mr(void)
+-- 
+2.11.0
+
@@ -0,0 +1,26 @@
+From 20f325051a66a31b0c6644e63cd2f8bb2b616e6e Mon Sep 17 00:00:00 2001
+From: Valentin Raevsky <valentin@compulab.co.il>
+Date: Mon, 20 Jul 2020 14:00:31 +0300
+Subject: [PATCH 067/126] imx8m-mini: env: Fix getopt_long() parameters' string
+
+Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
+---
+ tools/env/fw_env_main.c | 2 +-
+ 1 file changed, 1 insertion(+), 1 deletion(-)
+
+diff --git a/tools/env/fw_env_main.c b/tools/env/fw_env_main.c
+index ebd18b40ba..ca9ad78014 100644
+--- a/tools/env/fw_env_main.c
+++ b/tools/env/fw_env_main.c
+@@ -122,7 +122,7 @@ static void parse_common_args(int argc, char *argv[])
+ 	env_opts.config_file = CONFIG_FILE;
+ #endif
+ 
+-	while ((c = getopt_long(argc, argv, ":a:c:l:h:v:e", long_options, NULL)) !=
+	while ((c = getopt_long(argc, argv, ":a:c:l:h:ve", long_options, NULL)) !=
+ 	       EOF) {
+ 		switch (c) {
+ #ifdef CONFIG_FILE
+-- 
+2.11.0
+
@@ -0,0 +1,28 @@
+From 5368f1fce9510d82964e9cc38c76f754f2ff1355 Mon Sep 17 00:00:00 2001
+From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+Date: Wed, 22 Jul 2020 22:26:54 +0300
+Subject: [PATCH 068/126] ucm-imx8m-mini: Fix reset
+
+Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+---
+ configs/ucm-imx8m-mini_defconfig | 3 ---
+ 1 file changed, 3 deletions(-)
+
+diff --git a/configs/ucm-imx8m-mini_defconfig b/configs/ucm-imx8m-mini_defconfig
+index 2c98eaa256..ac8b3f558e 100644
+--- a/configs/ucm-imx8m-mini_defconfig
+++ b/configs/ucm-imx8m-mini_defconfig
+@@ -78,10 +78,7 @@ CONFIG_PINCTRL_IMX8M=y
+ CONFIG_DM_REGULATOR=y
+ CONFIG_DM_REGULATOR_FIXED=y
+ CONFIG_DM_REGULATOR_GPIO=y
+-CONFIG_DM_RESET=y
+ CONFIG_MXC_UART=y
+-CONFIG_SYSRESET=y
+-CONFIG_SYSRESET_PSCI=y
+ CONFIG_DM_THERMAL=y
+ CONFIG_NXP_TMU=y
+ CONFIG_USB=y
+-- 
+2.11.0
+
@@ -0,0 +1,30 @@
+From 0db9464775f4664c48b8428cdbd3cd70c87dea2c Mon Sep 17 00:00:00 2001
+From: Valentin Raevsky <valentin@compulab.co.il>
+Date: Wed, 5 Aug 2020 00:20:44 +0300
+Subject: [PATCH 069/126] imx8m-mini: spl: Add __weak
+ board_fit_config_name_match()
+
+Add __weak board_fit_config_name_match().
+Each board can redefind this function in its spl.c file.
+
+Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
+---
+ board/compulab/plat/imx8mm/spl/spl.c | 2 +-
+ 1 file changed, 1 insertion(+), 1 deletion(-)
+
+diff --git a/board/compulab/plat/imx8mm/spl/spl.c b/board/compulab/plat/imx8mm/spl/spl.c
+index ad1be9befd..63af88caa5 100644
+--- a/board/compulab/plat/imx8mm/spl/spl.c
+++ b/board/compulab/plat/imx8mm/spl/spl.c
+@@ -212,7 +212,7 @@ void spl_board_init(void)
+ }
+ 
+ #ifdef CONFIG_SPL_LOAD_FIT
+-int board_fit_config_name_match(const char *name)
+__weak int board_fit_config_name_match(const char *name)
+ {
+ 	/* Just empty function now - can't decide what to choose */
+ 	debug("%s: %s\n", __func__, name);
+-- 
+2.11.0
+
@@ -0,0 +1,32 @@
+From 447d297f3b0fbc8f2c02d99bc79215a01a7f27f7 Mon Sep 17 00:00:00 2001
+From: Valentin Raevsky <valentin@compulab.co.il>
+Date: Wed, 5 Aug 2020 00:22:29 +0300
+Subject: [PATCH 070/126] mcm-imx8m-mini: spl: Add
+ board_fit_config_name_match()
+
+Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
+---
+ board/compulab/mcm-imx8m-mini/spl.c | 10 ++++++++++
+ 1 file changed, 10 insertions(+)
+
+diff --git a/board/compulab/mcm-imx8m-mini/spl.c b/board/compulab/mcm-imx8m-mini/spl.c
+index d6ece8ef3e..1a208e09a4 100644
+--- a/board/compulab/mcm-imx8m-mini/spl.c
+++ b/board/compulab/mcm-imx8m-mini/spl.c
+@@ -7,3 +7,13 @@
+ int spl_board_private_init(void) {
+ 	return 0;
+ }
+
+#ifdef CONFIG_SPL_LOAD_FIT
+int board_fit_config_name_match(const char *name)
+{
+	/* Just empty function now - can't decide what to choose */
+	debug("%s: %s\n", __func__, name);
+
+	return 0;
+}
+#endif
+-- 
+2.11.0
+
@@ -0,0 +1,51 @@
+From 6815fe714952f3ee9e044e3ad14a3feb83857ca6 Mon Sep 17 00:00:00 2001
+From: Valentin Raevsky <valentin@compulab.co.il>
+Date: Wed, 5 Aug 2020 00:25:22 +0300
+Subject: [PATCH 071/126] imx8m-mini: u-boot: Add __weak
+ uboot_board_private_init()
+
+Add a __weak uboot_board_private_init().
+Each board can redefind this function in its board.c file.
+
+Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
+---
+ board/compulab/plat/imx8mm/board/board.c | 10 ++++++++++
+ 1 file changed, 10 insertions(+)
+
+diff --git a/board/compulab/plat/imx8mm/board/board.c b/board/compulab/plat/imx8mm/board/board.c
+index 819e6ef32c..2d12861bb8 100644
+--- a/board/compulab/plat/imx8mm/board/board.c
+++ b/board/compulab/plat/imx8mm/board/board.c
+@@ -7,6 +7,7 @@
+ #include <common.h>
+ #include <malloc.h>
+ #include <errno.h>
+#include <hang.h>
+ #include <asm/io.h>
+ #include <miiphy.h>
+ #include <netdev.h>
+@@ -167,12 +168,21 @@ int board_usb_cleanup(int index, enum usb_init_type init)
+ 
+ 	return 0;
+ }
+
+__weak int uboot_board_private_init(void) {
+	return 0;
+}
+
+ int board_init(void)
+ {
+ 
+ #ifdef CONFIG_FEC_MXC
+ 	setup_fec();
+ #endif
+	if (uboot_board_private_init()) {
+		printf("uboot_board_private_init() failed\n");
+		hang();
+	}
+ 	return 0;
+ }
+ 
+-- 
+2.11.0
+
@@ -0,0 +1,26 @@
+From 24922199f7e640a0dc20042bdc0ffaa900f85896 Mon Sep 17 00:00:00 2001
+From: Valentin Raevsky <valentin@compulab.co.il>
+Date: Wed, 5 Aug 2020 00:26:12 +0300
+Subject: [PATCH 072/126] mcm-imx8m-mini: u-boot: Add
+ uboot_board_private_init()
+
+Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
+---
+ board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c | 4 ++++
+ 1 file changed, 4 insertions(+)
+
+diff --git a/board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c b/board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c
+index 6cafc259e9..bd863f154f 100644
+--- a/board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c
+++ b/board/compulab/mcm-imx8m-mini/mcm-imx8m-mini.c
+@@ -28,3 +28,7 @@
+ #include <asm/mach-imx/video.h>
+ 
+ DECLARE_GLOBAL_DATA_PTR;
+
+int uboot_board_private_init(void) {
+	return 0;
+}
+-- 
+2.11.0
+
@@ -0,0 +1,29 @@
+From afa38bc44bb5b3054439f83173f95f28018064dd Mon Sep 17 00:00:00 2001
+From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+Date: Wed, 19 Aug 2020 18:45:55 +0300
+Subject: [PATCH 073/126] Add ddr_init return handling
+
+Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+---
+ board/compulab/plat/imx8mm/ddr/ddr.c | 5 ++++-
+ 1 file changed, 4 insertions(+), 1 deletion(-)
+
+diff --git a/board/compulab/plat/imx8mm/ddr/ddr.c b/board/compulab/plat/imx8mm/ddr/ddr.c
+index 4d774835ef..3912de6316 100644
+--- a/board/compulab/plat/imx8mm/ddr/ddr.c
+++ b/board/compulab/plat/imx8mm/ddr/ddr.c
+@@ -152,7 +152,10 @@ void spl_dram_init(void)
+ 	printf("DDRINFO(%s): %s %dG @ %d MHz\n", (ddr_found ? "D" : "?" ), lpddr4_array[i].name,
+ 			lpddr4_array[i].size, lpddr4_array[i].timing->fsp_table[0]);
+ 
+-	ddr_init(lpddr4_array[i].timing);
+	if (ddr_init(lpddr4_array[i].timing)) {
+		SPL_TCM_INIT;
+		do_reset(NULL,0,0,NULL);
+	}
+ 
+ 	ddr_info_mrr = lpddr4_get_mr();
+ 	if (ddr_info_mrr == 0xFFFFFFFF ) {
+-- 
+2.11.0
+
@@ -0,0 +1,121 @@
+From 2daab9bfa0085f0b3ed0587128327b14b03fa302 Mon Sep 17 00:00:00 2001
+From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+Date: Tue, 18 Aug 2020 19:10:19 +0300
+Subject: [PATCH 074/126] spl: Enable Kingston DRAM support
+
+Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+---
+ board/compulab/plat/imx8/eeprom/eeprom_spl.c | 21 +++++++++++++++++++++
+ board/compulab/plat/imx8mm/ddr/ddr.c         | 27 ++++++++++++++++++++-------
+ 2 files changed, 41 insertions(+), 7 deletions(-)
+
+diff --git a/board/compulab/plat/imx8/eeprom/eeprom_spl.c b/board/compulab/plat/imx8/eeprom/eeprom_spl.c
+index 79b2e29c63..b3c894a9af 100644
+--- a/board/compulab/plat/imx8/eeprom/eeprom_spl.c
+++ b/board/compulab/plat/imx8/eeprom/eeprom_spl.c
+@@ -79,6 +79,10 @@ static int cl_eeprom_write(uint offset, uchar *buf, int len)
+ #define BOARD_DDRINFO_SIZE 4
+ static u32 board_ddrinfo = 0xdeadbeef;
+ 
+#define BOARD_DDRSUBIND_OFFSET 0x44
+#define BOARD_DDRSUBIND_SIZE 1
+static u8 board_ddrsubind = 0xff;
+
+ #define BOARD_DRATE_OFFSET 0x50
+ #define BOARD_DRATE_SIZE 4
+ static u32 board_drate = 0xdeadbeef;
+@@ -129,6 +133,23 @@ u32 cl_eeprom_set_drate(u32 drate, unsigned int r, unsigned int c)
+ 	return board_drate;
+ };
+ 
+u8 cl_eeprom_get_subind(void)
+{
+	if (cl_eeprom_read(BOARD_DDRSUBIND_OFFSET, (uchar *)&board_ddrsubind, BOARD_DDRSUBIND_SIZE))
+		return 0xff;
+
+	return board_ddrsubind;
+};
+
+u8 cl_eeprom_set_subind(u8 ddrsubind)
+{
+	if (cl_eeprom_write(BOARD_DDRSUBIND_OFFSET, (uchar *)&ddrsubind, BOARD_DDRSUBIND_SIZE))
+		return 0xff;
+	board_ddrsubind = ddrsubind;
+
+	return board_ddrsubind;
+};
+
+ /* override-size ifaces */
+ u32 cl_eeprom_get_osize(void)
+ {
+diff --git a/board/compulab/plat/imx8mm/ddr/ddr.c b/board/compulab/plat/imx8mm/ddr/ddr.c
+index 3912de6316..970d3ab81b 100644
+--- a/board/compulab/plat/imx8mm/ddr/ddr.c
+++ b/board/compulab/plat/imx8mm/ddr/ddr.c
+@@ -19,6 +19,8 @@
+ /* Forward declarations */
+ u32 cl_eeprom_get_ddrinfo(void);
+ u32 cl_eeprom_set_ddrinfo(u32 ddrinfo);
+u32 cl_eeprom_get_subind(void);
+u32 cl_eeprom_set_subind(u32 subind);
+ 
+ u32 cl_eeprom_get_osize(void);
+ 
+@@ -57,17 +59,24 @@ struct lpddr4_desc {
+ 	 * use it if default is not the
+ 	 * 1-st array entry */
+ 	unsigned int _default;
+	/* An optional field to distiguish DRAM chips that
+	 * have different geometry, though return the same MRR.
+	 * Default value 0xff
+	 */
+	u8	subind;
+ 	struct dram_timing_info *timing;
+ 	char *desc[4];
+ };
+ 
+ #define DEFAULT (('D' << 24) + ('E' << 16 ) + ( 'F' << 8 ) + 'A')
+ static const struct lpddr4_desc lpddr4_array[] = {
+-	{ .name = "Nanya",  .id = 0x01050008, .size = 1024, .count = 1, .timing = &ucm_dram_timing_01050008}, //Only the first timing entry is in use
+-	{ .name = "Nanya",  .id = 0x05000010, .size = 2048, .count = 1, .timing = &ucm_dram_timing_01061010},
+-	{ .name = "Samsung",.id = 0x01061010, .size = 2048, .count = 1, .timing = &ucm_dram_timing_01061010},
+-	{ .name = "Micron", .id = 0xff020008, .size = 2048, .count = 1, .timing = &ucm_dram_timing_ff020008},
+-	{ .name = "Micron", .id = 0xff000110, .size = 4096, .count = 1, .timing = &ucm_dram_timing_ff000110},
+	{ .name = "Nanya",	.id = 0x05000010, .subind = 0xff, .size = 2048, .count = 1, .timing = &ucm_dram_timing_01061010},
+	{ .name = "Samsung",	.id = 0x01061010, .subind = 0xff, .size = 2048, .count = 1, .timing = &ucm_dram_timing_01061010},
+	{ .name = "Samsung",	.id = 0x01050008, .subind = 0xff, .size = 1024, .count = 1, .timing = &ucm_dram_timing_01050008},
+	{ .name = "Kingston",	.id = 0xff000010, .subind = 0x04, .size = 4096, .count = 1, .timing = &ucm_dram_timing_ff000110},
+	{ .name = "Kingston",	.id = 0xff000010, .subind = 0x02, .size = 2048, .count = 1, .timing = &ucm_dram_timing_01061010},
+	{ .name = "Micron",	.id = 0xff020008, .subind = 0xff, .size = 2048, .count = 1, .timing = &ucm_dram_timing_ff020008},
+	{ .name = "Micron",	.id = 0xff000110, .subind = 0xff, .size = 4096, .count = 1, .timing = &ucm_dram_timing_ff000110},
+ };
+ 
+ static unsigned int lpddr4_get_mr(void)
+@@ -122,7 +131,8 @@ void spl_dram_init(void)
+ 		/* get ddr type from the eeprom if not in tcm scan mode */
+ 		ddr_info = cl_eeprom_get_ddrinfo();
+ 		for ( i = 0; i < ARRAY_SIZE(lpddr4_array); i++ ) {
+-			if (lpddr4_array[i].id == ddr_info) {
+			if (lpddr4_array[i].id == ddr_info &&
+			lpddr4_array[i].subind == cl_eeprom_get_subind()) {
+ 				ddr_found = 1;
+ 				break;
+ 			}
+@@ -177,10 +187,13 @@ void spl_dram_init(void)
+ 	if (ddr_found == 0) {
+ 		/* Update eeprom */
+ 		cl_eeprom_set_ddrinfo(ddr_info_mrr);
+		mdelay(10);
+ 		ddr_info = cl_eeprom_get_ddrinfo();
+		mdelay(10);
+		cl_eeprom_set_subind(lpddr4_array[i].subind);
+ 		/* make sure that the ddr_info has reached the eeprom */
+ 		printf("DDRINFO(E): mr5-8 [ 0x%x ], read back\n", ddr_info);
+-		if (ddr_info_mrr != ddr_info) {
+		if (ddr_info_mrr != ddr_info || cl_eeprom_get_subind() != lpddr4_array[i].subind) {
+ 			printf("DDRINFO(EEPROM): make sure that the eeprom is accessible\n");
+ 			printf("DDRINFO(EEPROM): i2c dev 1; i2c md 0x51 0x40 0x50\n");
+ 		}
+-- 
+2.11.0
+
@@ -0,0 +1,276 @@
+From 218460565b10716a8bc5aa1215f8a3449ea6fb9b Mon Sep 17 00:00:00 2001
+From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+Date: Sat, 29 Aug 2020 22:14:48 +0300
+Subject: [PATCH 075/126] Add show_suite function
+
+The function shows product names of UCM and SB on boot.
+
+Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+---
+ arch/arm/dts/cpl-imx8m-mini.dtsi         |  2 +-
+ board/compulab/common/eeprom.c           | 88 ++++++++++++++++++++++++--------
+ board/compulab/common/eeprom.h           |  1 +
+ board/compulab/plat/imx8mm/board/board.c | 17 ++++++
+ 4 files changed, 87 insertions(+), 21 deletions(-)
+
+diff --git a/arch/arm/dts/cpl-imx8m-mini.dtsi b/arch/arm/dts/cpl-imx8m-mini.dtsi
+index 4f9c5fbfb9..a587c3dda0 100644
+--- a/arch/arm/dts/cpl-imx8m-mini.dtsi
+++ b/arch/arm/dts/cpl-imx8m-mini.dtsi
+@@ -226,7 +226,7 @@
+ 	clock-frequency = <400000>;
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&pinctrl_i2c1>;
+-	status = "disabled";
+	status = "okay";
+ 
+ };
+ 
+diff --git a/board/compulab/common/eeprom.c b/board/compulab/common/eeprom.c
+index defd9b6446..46363c0707 100644
+--- a/board/compulab/common/eeprom.c
+++ b/board/compulab/common/eeprom.c
+@@ -7,6 +7,7 @@
+  * SPDX-License-Identifier:	GPL-2.0+
+  */
+ 
+#include <linux/ctype.h>
+ #include <common.h>
+ #include <asm/mach-imx/mxc_i2c.h>
+ #include <i2c.h>
+@@ -22,8 +23,16 @@
+ # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+ #endif
+ 
+#ifndef CONFIG_SYS_I2C_EEPROM_ADDR_SB
+# define CONFIG_SYS_I2C_EEPROM_ADDR_SB	0x54
+#endif
+
+ #ifndef CONFIG_SYS_I2C_EEPROM_BUS
+-#define CONFIG_SYS_I2C_EEPROM_BUS	0
+# define CONFIG_SYS_I2C_EEPROM_BUS	1
+#endif
+
+#ifndef CONFIG_SYS_I2C_EEPROM_BUS_SB
+# define CONFIG_SYS_I2C_EEPROM_BUS_SB	0
+ #endif
+ 
+ #define EEPROM_LAYOUT_VER_OFFSET	44
+@@ -40,31 +49,43 @@
+ #define LAYOUT_INVALID	0
+ #define LAYOUT_LEGACY	0xff
+ 
+-static int cl_eeprom_bus;
+ static int cl_eeprom_layout; /* Implicitly LAYOUT_INVALID */
+ 
+-static struct udevice  *g_dev = NULL;
+struct eeprom_path {
+	int bus;
+	uint8_t chip;
+};
+ 
+-static int cpl_eeprom_init(void) {
+static const struct eeprom_path eeprom_som = {
+	CONFIG_SYS_I2C_EEPROM_BUS,
+	CONFIG_SYS_I2C_EEPROM_ADDR
+};
+static const struct eeprom_path eeprom_sb = {
+	CONFIG_SYS_I2C_EEPROM_BUS_SB,
+	CONFIG_SYS_I2C_EEPROM_ADDR_SB
+};
+
+static const struct eeprom_path *working_eeprom;
+ 
+-	int i2c_bus = CONFIG_SYS_I2C_EEPROM_BUS;
+-	uint8_t chip = CONFIG_SYS_I2C_EEPROM_ADDR;
+static struct udevice *g_dev = NULL;
+
+static int cpl_eeprom_init(void) {
+ 
+ 	struct udevice *bus, *dev;
+ 	int ret;
+ 
+ 	if (!g_dev) {
+ 
+-		ret = uclass_get_device_by_seq(UCLASS_I2C, i2c_bus, &bus);
+		ret = uclass_get_device_by_seq(UCLASS_I2C, working_eeprom->bus, &bus);
+ 		if (ret) {
+-			printf("%s: No bus %d\n", __func__, i2c_bus);
+			printf("%s: No bus %d\n", __func__, working_eeprom->bus);
+ 			return ret;
+ 		}
+ 
+-		ret = dm_i2c_probe(bus, chip, 0, &dev);
+		ret = dm_i2c_probe(bus, working_eeprom->chip, 0, &dev);
+ 		if (ret) {
+ 			printf("%s: Can't find device id=0x%x, on bus %d\n",
+-				__func__, chip, i2c_bus);
+				__func__, working_eeprom->chip, working_eeprom->bus);
+ 			return ret;
+ 		}
+ 
+@@ -88,7 +109,7 @@ static int cl_eeprom_read(uint offset, uchar *buf, int len)
+ 	return res;
+ }
+ 
+-static int cl_eeprom_setup(uint eeprom_bus)
+static int cl_eeprom_setup(const struct eeprom_path *eeprom)
+ {
+ 	int res;
+ 
+@@ -96,10 +117,11 @@ static int cl_eeprom_setup(uint eeprom_bus)
+ 	 * We know the setup was already done when the layout is set to a valid
+ 	 * value and we're using the same bus as before.
+ 	 */
+-	if (cl_eeprom_layout != LAYOUT_INVALID && eeprom_bus == cl_eeprom_bus)
+	if (cl_eeprom_layout != LAYOUT_INVALID && eeprom == working_eeprom)
+ 		return 0;
+ 
+-	cl_eeprom_bus = eeprom_bus;
+	working_eeprom = eeprom;
+	g_dev = NULL;
+ 	res = cl_eeprom_read(EEPROM_LAYOUT_VER_OFFSET,
+ 			     (uchar *)&cl_eeprom_layout, 1);
+ 	if (res) {
+@@ -120,7 +142,7 @@ void cpl_get_board_serial(struct tag_serialnr *serialnr)
+ 
+ 	memset(serialnr, 0, sizeof(*serialnr));
+ 
+-	if (cl_eeprom_setup(CONFIG_SYS_I2C_EEPROM_BUS))
+	if (cl_eeprom_setup(&eeprom_som))
+ 		return;
+ 
+ 	offset = (cl_eeprom_layout != LAYOUT_LEGACY) ?
+@@ -139,12 +161,12 @@ void cpl_get_board_serial(struct tag_serialnr *serialnr)
+  * Routine: cl_eeprom_read_mac_addr
+  * Description: read mac address and store it in buf.
+  */
+-int cl_eeprom_read_mac_addr(uchar *buf, uint eeprom_bus)
+int cl_eeprom_read_mac_addr(uchar *buf, uint eeprom_bus __attribute__((unused)))
+ {
+ 	uint offset;
+ 	int err;
+ 
+-	err = cl_eeprom_setup(eeprom_bus);
+	err = cl_eeprom_setup(&eeprom_som);
+ 	if (err)
+ 		return err;
+ 
+@@ -160,7 +182,7 @@ static u32 board_rev;
+  * Routine: cl_eeprom_get_board_rev
+  * Description: read system revision from eeprom
+  */
+-u32 cl_eeprom_get_board_rev(uint eeprom_bus)
+u32 cl_eeprom_get_board_rev(uint eeprom_bus __attribute__((unused)))
+ {
+ 	char str[5]; /* Legacy representation can contain at most 4 digits */
+ 	uint offset = BOARD_REV_OFFSET_LEGACY;
+@@ -168,7 +190,7 @@ u32 cl_eeprom_get_board_rev(uint eeprom_bus)
+ 	if (board_rev)
+ 		return board_rev;
+ 
+-	if (cl_eeprom_setup(eeprom_bus))
+	if (cl_eeprom_setup(&eeprom_som))
+ 		return 0;
+ 
+ 	if (cl_eeprom_layout != LAYOUT_LEGACY)
+@@ -198,14 +220,14 @@ u32 cl_eeprom_get_board_rev(uint eeprom_bus)
+  *
+  * @return: 0 on success, < 0 on failure
+  */
+-int cl_eeprom_get_product_name(uchar *buf, uint eeprom_bus)
+int cl_eeprom_get_product_name(uchar *buf, uint eeprom_bus __attribute__((unused)))
+ {
+ 	int err;
+ 
+ 	if (buf == NULL)
+ 		return -EINVAL;
+ 
+-	err = cl_eeprom_setup(eeprom_bus);
+	err = cl_eeprom_setup(&eeprom_som);
+ 	if (err)
+ 		return err;
+ 
+@@ -216,6 +238,32 @@ int cl_eeprom_get_product_name(uchar *buf, uint eeprom_bus)
+ 	return err;
+ }
+ 
+static int cl_eeprom_read_product_name(char *buf, const struct eeprom_path *eeprom)
+{
+	int len;
+	int err;
+	uchar tmp[PRODUCT_NAME_SIZE];
+
+	err = cl_eeprom_setup(eeprom);
+	if (err)
+		printf("%s: Error accesing i2c %x@%x\n", __func__, eeprom->bus, eeprom->chip);
+	else
+		err = cl_eeprom_read(PRODUCT_NAME_OFFSET, tmp, PRODUCT_NAME_SIZE);
+
+	if (!err && tmp[0] != 0xff) // Check if the flash isn't written
+		len = snprintf(buf, PRODUCT_NAME_SIZE, (char*)tmp);
+	else
+		len = snprintf(buf, PRODUCT_NAME_SIZE, "unknown");
+
+	return len;
+}
+void cl_eeprom_get_suite(char *buf)
+{
+	buf += cl_eeprom_read_product_name(buf, &eeprom_som);
+	buf += sprintf(buf, " @ ");
+	buf += cl_eeprom_read_product_name(buf, &eeprom_sb);
+}
+
+ #ifdef CONFIG_CMD_EEPROM_LAYOUT
+ /**
+  * eeprom_field_print_bin_ver() - print a "version field" which contains binary
+diff --git a/board/compulab/common/eeprom.h b/board/compulab/common/eeprom.h
+index 09804ee146..d366f59288 100644
+--- a/board/compulab/common/eeprom.h
+++ b/board/compulab/common/eeprom.h
+@@ -15,6 +15,7 @@
+ int cl_eeprom_read_mac_addr(uchar *buf, uint eeprom_bus);
+ u32 cl_eeprom_get_board_rev(uint eeprom_bus);
+ int cl_eeprom_get_product_name(uchar *buf, uint eeprom_bus);
+void cl_eeprom_get_suite(char* buf);
+ #else
+ static inline int cl_eeprom_read_mac_addr(uchar *buf, uint eeprom_bus)
+ {
+diff --git a/board/compulab/plat/imx8mm/board/board.c b/board/compulab/plat/imx8mm/board/board.c
+index 2d12861bb8..4ec5a5af4f 100644
+--- a/board/compulab/plat/imx8mm/board/board.c
+++ b/board/compulab/plat/imx8mm/board/board.c
+@@ -173,6 +173,22 @@ __weak int uboot_board_private_init(void) {
+ 	return 0;
+ }
+ 
+static void show_suite_info(void)
+{
+	char *buf = malloc(200); //More than necessary
+
+	if(!buf) {
+		printf("%s: Not enough memory\n", __func__);
+		return;
+	}
+
+	cl_eeprom_get_suite(buf);
+	printf("Suite:\t%s\n", buf);
+
+	free(buf);
+	return;
+}
+
+ int board_init(void)
+ {
+ 
+@@ -183,6 +199,7 @@ int board_init(void)
+ 		printf("uboot_board_private_init() failed\n");
+ 		hang();
+ 	}
+	show_suite_info();
+ 	return 0;
+ }
+ 
+-- 
+2.11.0
+
@@ -0,0 +1,26 @@
+From debba895d9bbb88e1b855417e6448cd96fed978b Mon Sep 17 00:00:00 2001
+From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+Date: Sat, 29 Aug 2020 22:37:39 +0300
+Subject: [PATCH 076/126] Clean debug printout
+
+Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+---
+ board/compulab/common/eeprom.c | 2 +-
+ 1 file changed, 1 insertion(+), 1 deletion(-)
+
+diff --git a/board/compulab/common/eeprom.c b/board/compulab/common/eeprom.c
+index 46363c0707..ebcafac04b 100644
+--- a/board/compulab/common/eeprom.c
+++ b/board/compulab/common/eeprom.c
+@@ -260,7 +260,7 @@ static int cl_eeprom_read_product_name(char *buf, const struct eeprom_path *eepr
+ void cl_eeprom_get_suite(char *buf)
+ {
+ 	buf += cl_eeprom_read_product_name(buf, &eeprom_som);
+-	buf += sprintf(buf, " @ ");
+	buf += sprintf(buf, " on ");
+ 	buf += cl_eeprom_read_product_name(buf, &eeprom_sb);
+ }
+ 
+-- 
+2.11.0
+
@@ -0,0 +1,78 @@
+From 7c45580b9dd2ca23e663375ac138c9bfb760cbdb Mon Sep 17 00:00:00 2001
+From: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+Date: Wed, 2 Sep 2020 23:11:10 +0300
+Subject: [PATCH 078/126] ucm-imx8m-mini: Enable status LED and cmd led
+
+Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
+---
+ arch/arm/dts/ucm-imx8m-mini.dts          | 20 ++++++++++++++++++++
+ board/compulab/plat/imx8mm/board/board.c |  3 +++
+ configs/ucm-imx8m-mini_defconfig         |  5 ++++-
+ 3 files changed, 27 insertions(+), 1 deletion(-)
+
+diff --git a/arch/arm/dts/ucm-imx8m-mini.dts b/arch/arm/dts/ucm-imx8m-mini.dts
+index 7b81e8a75b..ba0e169004 100644
+--- a/arch/arm/dts/ucm-imx8m-mini.dts
+++ b/arch/arm/dts/ucm-imx8m-mini.dts
+@@ -19,4 +19,24 @@
+ / {
+ 	model = "CompuLab UCM-iMX8M-Mini board";
+ 	compatible = "cpl,ucm-imx8m-mini", "fsl,imx8mm-evk", "fsl,imx8mm";
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_led>;
+
+		status_led {
+			label = "status";
+			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl_gpio_led: gpioledgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x19
+		>;
+	};
+ };
+diff --git a/board/compulab/plat/imx8mm/board/board.c b/board/compulab/plat/imx8mm/board/board.c
+index 4ec5a5af4f..03e479ee57 100644
+--- a/board/compulab/plat/imx8mm/board/board.c
+++ b/board/compulab/plat/imx8mm/board/board.c
+@@ -199,6 +199,9 @@ int board_init(void)
+ 		printf("uboot_board_private_init() failed\n");
+ 		hang();
+ 	}
+	if (IS_ENABLED(CONFIG_LED))
+		led_default_state();
+
+ 	show_suite_info();
+ 	return 0;
+ }
+diff --git a/configs/ucm-imx8m-mini_defconfig b/configs/ucm-imx8m-mini_defconfig
+index ac8b3f558e..7d4b487ce9 100644
+--- a/configs/ucm-imx8m-mini_defconfig
+++ b/configs/ucm-imx8m-mini_defconfig
+@@ -45,7 +45,7 @@ CONFIG_CMD_DHCP=y
+ CONFIG_CMD_MII=y
+ CONFIG_CMD_PING=y
+ CONFIG_CMD_CACHE=y
+-CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_REGULATOR=
+ CONFIG_CMD_EXT2=y
+ CONFIG_CMD_EXT4=y
+ CONFIG_CMD_FAT=y
+@@ -97,3 +97,6 @@ CONFIG_EXT4_WRITE=y
+ CONFIG_FAT_WRITE=y
+ CONFIG_OF_LIBFDT_OVERLAY=y
+ # CONFIG_EFI_LOADER is not set
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+
+-- 
+2.11.0
+
--- a/Show More
+++ b/Show More