This handles toolchain failures per-file. The intent is to allow placing
both "success" and "fail" tests in the same file, using splits. However,
this PR only adds support and updates existing tests to continue
passing.
A lot of this is more boring "remove unused header", plus some other
minor cleanups. I think the most significant changes were:
- yaml_test_helpers.cpp is doing a switch on an unsigned int, comparing
to enum values.
-
[bugprone-switch-missing-default-case](https://clang.llvm.org/extra/clang-tidy/checks/bugprone/switch-missing-default-case.html)
is unhappy with EnumBase, but correctly identified
yaml_test_helpers.cpp, so I'm opting to address it rather than disabling
it even though it needs NOLINT in several locations as a result, in
addition to what I think are some low-value `default` cases. I'd be fine
going the other way with this too and disabling it globally (I could see
it being noisier in the explorer).
- MarkInitializerFor swaps the argument names between the .h and .cpp. I
think the .cpp had the order as intended.
- There's a new-ish
[performance-enum-size](https://clang.llvm.org/extra/clang-tidy/checks/performance/enum-size.html)
which I'm basically treating as "add int8_t to enums".
My main motivation here is to just clean up as many of these as I can so
that I stop seeing them in vscode.
This also tries to restructure the command line interface to the
toolchain a bit to make it start operating more like a compiler that
could be integrated into a build system rather than primarily as
a testing tool.
1) This switches form a `dump` subcommand to a `compile` subcommand
which has "dump" actions that can be enabled within it.
2) A distinct set of compile _phases_ that match the toolchain
structure:
- `lex` to run the lexer
- `parse` to run the parser
- `check` to fully check that the code is valid
- `lower` to lower to LLVM's IR
- `codegen` to generate executable code
3) The codegen phase has two output formats: textual assembly and
a binary object. These outputs can be configured, with a default for
an object when writing to a file and more firm default for textual
assembly when writing to stdout.
4) Select and expose the use of the LLVM host detection to compute
a default code generation target in the driver so that the command
line interface can reflect this. For example, the `help` output will
include the default target.
5) The `//toolchain/codegen` library APIs have been restructured a bit
to make the code flow a bit more naturally when implementing the new
command line structure. No real changes to the logic though.
There are also some minor tweaks to the command line interface based on
trying to use the shortest names for things that still seem likely to be
learnable for users:
- Switched `target-triple` to just `target`: the "triple" component to
this name is historical and can be confusing. For example, almost all
"triple" strings have more than three components today.
- Switched to just `--output` as now the fact that it is a file can be
configured in the documentation -- it will render as `--output=FILE`.
This also adds support for two custom output filename modes. First, when
no output is specified, we now compute one in the conventional way for
compilers by removing the file extension of the input file and replacing
it with `.o` for an object file output or `.s` for an assembly file
output. This matches the behavior of Clang and GCC for example.
Second, output to stdout is enabled with the special output file name of
`-` since it is no longer the default. This also follows the convention
of most compilers and many other command line tools to use `-` as a file
name to signify using standard in/out pipes.
There are still some rough edges here that I suspect could be improved,
but this seems like a good start of switching over to a complete
argument parser.
---------
Co-authored-by: Jon Ross-Perkins <jperkins@google.com>
Co-authored-by: Lucile Rose Nihlen <luci.the.rose@gmail.com>
Co-authored-by: Richard Smith <richard@metafoo.co.uk>
The lack of comments makes it difficult to be sure, but if any of these
are necessary, I'd like to make sure there are comments to explain why a
specific value was shown (which I do add for diagnostics_ in this
change).
Replacing direct raw_string_ostream uses. I figure the wrapper should be used more consistently.
There are still remaining raw_string_ostream uses that weren't compatible -- I'm continuing to look at those, but felt it was cleaner to have this on its own.
This adds vfs support to the toolchain, allowing Driver to take in-memory inputs in tests. As a consequence, I'm simplifying SourceBuffer: rather than allowing tests to pass in their own memory buffer, I'm using InMemoryFileSystem to push for greater consistency with production code. This does hit a quirk where I need to be careful about null terminator handling because fuzzer imports don't always have one, but that's probably more robust anyways.
Co-authored-by: Richard Smith <richard@metafoo.co.uk>
The small size is for the 1m vs 5m time limit -- all these tests _should_ be fast so a lower limit seems consistent, and the 5m timeout was getting in my way when trying to debug *actual* timeouts.
The Carbon::Testing bit is for convenience -- test libraries are generally using it, it seems like the tests should too. Note this reduces the need for `using`.
This does push NodeMatchers into Carbon::Testing -- I don't think this was benefiting from having its own namespace; `using namespace` is discouraged [under style](https://google.github.io/styleguide/cppguide.html#Namespaces), we wouldn't support an equivalent in Carbon, and it feels like it's not helping to avoid name collisions. (also tidy was bugging about it, and while I could NOLINT that, this felt like the better approach)
This should clean up our top level directory and the build patterns.
No non-mechanical edits here. Just injecting `toolchain/` and
`TOOLCHAIN_` and then running formatting tools.
Jon Ross-Perkins
Jon Meow