When performing a call through an impl witness, the callee that we
type-check against is the function in the interface, so we form a
specific for that callee. However, once the impl witness access
resolves, the eventual callee is a different function -- the function in
the impl -- so this would cause us to form a `SpecificFunction` where
the callee is one function but the specific refers to a different
function.
Address this by adding another instruction, `SpecificImplFunction`, that
takes a function in an impl and a specific for the corresponding
function in the interface, and computes and returns a `SpecificFunction`
referring to the corresponding specific function in the impl, or returns
a direct reference to the function in the `impl` if it's not a generic
function.
A query facet type may contain multiple required interfaces, in which
case impl lookup should return an ImplWitness for an impl that is used
for each interface in the query. We bundle these together into an
instruction block and return that from impl lookup. The witnesses are in
the same order as the interfaces in the
`CompleteFacetType::required_interfaces`. This allows walking the
`required_interfaces` to find an interface to give an index that can
also be used to grab a witness from this set, or from FacetValue.
FacetValue now has an InstBlockId for the set of witnesses of the
FacetType, instead of a single ImplWitness instruction id.
FacetAccessWitness includes the index of the witness (determined from
the position in `required_interfaces`) of the witness it's accessing
from the FacetType.
The
toolchain/check/testdata/facet/no_prelude/fail_todo_call_combined_impl_witness.carbon
test demonstrates the fix in the resulting SemIR. We can see the calls
to methods on a multi-interface FacetType result in a FacetAccessWitness
with an index of the correct interface, and this results in a witness
that leads to the correct impl's function.
There is a TODO in member access, where it does not have a
`CompleteFacetType` yet, so it uses the index in
`FacetTypeInfo::impls_constraints` instead, but this can be incorrect in
the presence of named constraints, which when completed can add more
interfaces to the `CompleteFacetType` and which are sorted into an
arbitrary order with the rest there.
---------
Co-authored-by: josh11b <15258583+josh11b@users.noreply.github.com>
If the query facet type has more than one interface, we must find an
impl that provides that interface for the query type for each interface.
This just looks like a for loop over the interfaces and ensuring we
found one impl witness for every one.
However the impl matching must change since it can't look at the
constant value of the entire query facet type for comparison with the
impl, as that query facet type may be for multiple interfaces and we are
looking to match an impl of a single interface.
To do this we break the query facet type up into each interface and make
sure the interface ids match. Then ensure that the impl was able to
deduce any generic parameters using the specific of the single query
interface.
There are some TODOs left here:
1. If the facet type for the query or the impl constraint has
"other_requirements" then we can't verify that they match since they are
lost. We fall back to comparing the constant id of the query to the
impl's constraint (after deducing generics in the impl). This correctly
eliminates mismatches but eagerly eliminates impls that could match the
query interface as well when there's more than one interface in the
query.
2. We don't return a witness for every interface in the query facet
type. Since we can't demonstrate any use of the witness there yet, for
cases that can have more than one interface in the query facet type,
this doesn't break anything that was previously working. The return
value is currently treated as a bool for cases with multiple interfaces
in the facet type (as a test for "can this be converted") but the
converted-to facet value's witnesses are unused.
---------
Co-authored-by: josh11b <15258583+josh11b@users.noreply.github.com>